Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Problems
  3. Washer Repair
  4. Washer Not Spinning
Washer Repair · Houston, TX

Washer not spinning or leaving clothes soaking wet?

Clothes that come out dripping mean the final spin didn't happen or ran slowly. Depending on the machine, that's a lid lock, a door lock, a worn belt, a motor coupling, a shift actuator or an unbalanced load the control refused to spin.

One visit, 30–75 minutes Same-day in most of Houston 1-year parts, 90-day labor warranty
Quick diagnosis
Most likely cause
A failed lid lock, door lock or drive component
Typical repair time
One visit, 30–75 minutes
Service call
$89 diagnostic, credited to the repair

Why it's happening, in order of likelihood

Our technicians test in roughly this order. The numbers reflect how often each cause turns out to be the fault on Houston service calls.

  1. 1

    Lid lock or door lock

    No lock, no spin. The most common cause on top loaders built in the last 12 years.

  2. 2

    Drive belt

    Belt-driven machines lose the belt or glaze it; the motor runs but the tub doesn't.

  3. 3

    Motor coupling (older Whirlpool direct-drive)

    A small plastic coupling between motor and transmission that shears; the washer agitates weakly or not at all and won't spin.

  4. 4

    Shift actuator / mode shifter

    On newer top loaders, the actuator moves the drive between agitate and spin. When it fails, the machine agitates but won't spin, or logs F7 E1.

  5. 5

    Unbalanced load / suspension

    The control aborts a spin that would shake the machine apart. Worn suspension rods or shocks make every load look unbalanced.

  6. 6

    Drain fault

    The washer won't spin until the water is gone; a slow drain cancels the spin.

  7. 7

    Motor, clutch or transmission

    Clutch wear on older top loaders, motor or hall sensor on direct-drive machines.

Check these before you call

Safe, no-tools checks. If none of them solves it, the next step is a technician.

  • Redistribute the load and run a drain/spin; if it works, suspension is wearing.
  • Listen for the lid lock click when the cycle starts.
  • Check whether the tub is draining fully before the spin.
  • Open the lid during spin on an older machine: if the tub coasts freely by hand, suspect the coupling or belt.

Parts we typically replace

  • Lid lock
  • Door lock
  • Drive belt
  • Motor coupling
  • Shift actuator
  • Suspension rods / shocks
  • Clutch
  • Drain pump

Brand-specific notes

  • WhirlpoolWhirlpool, Maytag, Kenmore 110-series and Amana top loaders: F5 E2 means lid lock, F7 E1 means shift actuator or motor sensing.
  • LGLG LE means motor locked; UE means unbalanced.
  • GE AppliancesGE top loaders fail the mode shifter and lid lock most often.
  • SamsungSamsung UE/UC with a violent spin means suspension rods.

Repair or replace?

Lid locks, actuators, belts and couplings are inexpensive repairs. A transmission on a budget machine may not be.

What happens on the visit

1

Describe the symptom

Tell us the brand, model and what it's doing. A photo of the model tag helps.

2

We diagnose, you approve

$89 diagnostic, credited to the repair. Flat-rate quote before any work.

3

Fixed, usually that visit

Common parts are on the truck. 1-year parts, 90-day labor warranty on the repair.

Questions about this problem

Why does my washer spin slowly?
A slipping belt, a worn clutch or a control limiting speed for an unbalanced load.
Why does my washer stop with water in it and the lid locked?
Usually a drain fault; see washer not draining.

Related washing machine problems

Washer trouble? Same-day help.

Call or text (713) 548-7587 for a same-day appointment anywhere in Greater Houston. $89 diagnostic, credited toward your repair.

Call nowBook online