- Home
- Problems
- Oven & Range Repair
- Oven Not Heating
Oven not heating?
An oven that won't heat at all, or that heats very slowly, usually has one failed part: a gas igniter, a bake element, a temperature sensor, a thermal fuse or a control board relay. These are stocked parts and most repairs take under an hour.
- Most likely cause
- A weak gas igniter or a burned-out bake element
- Typical repair time
- One visit, 30–60 minutes
- Service call
- $89 diagnostic, credited to the repair
Why it's happening, in order of likelihood
Our technicians test in roughly this order. The numbers reflect how often each cause turns out to be the fault on Houston service calls.
- 1
Weak igniter (gas)
The igniter glows but no longer draws enough current to open the safety valve. The oven never lights, or lights after a long delay. This is the most common gas oven repair in Houston.
- 2
Bake or broil element (electric)
Look for a blister or break in the element; no red glow when set to bake.
- 3
Oven temperature sensor
An open sensor stops the oven from heating and usually throws an F3-type code.
- 4
Thermal fuse
Blows during a self-clean cycle; the oven goes dead or won't heat afterwards.
- 5
Control board relay
The board's bake relay fails; everything lights up but the element or igniter never gets power.
- 6
Safety gas valve (gas)
Rare, but a valve that won't open with a good igniter.
- 7
Power: breaker or wiring
Electric ranges need both legs of 240V; one leg lost means burners work but the oven doesn't.
Check these before you call
Safe, no-tools checks. If none of them solves it, the next step is a technician.
- Watch the igniter: if it glows for more than 90 seconds without lighting, it's weak.
- Electric: look at the bake element for a visible break; check the double breaker.
- Note any F-code on the display.
- If this started right after a self-clean, suspect the thermal fuse or door lock.
Parts we typically replace
- Oven igniter
- Bake element
- Broil element
- Oven temperature sensor
- Thermal fuse
- Control board
- Safety gas valve
Brand-specific notes
- WhirlpoolWhirlpool, Maytag, KitchenAid and JennAir ovens show F3 E0 for an open sensor.
- GE AppliancesGE and Café show F3 for the sensor and F2 for over-temperature.
- FrigidaireFrigidaire F30/F31 are sensor faults; F10 is runaway temperature.
- SamsungSamsung gas ranges: the oven igniter is the usual culprit.
- WolfWolf dual-fuel ovens: relay board or element; gas models the igniter.
Repair or replace?
Nearly always a repair.
What happens on the visit
Describe the symptom
Tell us the brand, model and what it's doing. A photo of the model tag helps.
We diagnose, you approve
$89 diagnostic, credited to the repair. Flat-rate quote before any work.
Fixed, usually that visit
Common parts are on the truck. 1-year parts, 90-day labor warranty on the repair.
Questions about this problem
Why does my gas oven smell like gas before it lights?
Why do my burners work but the oven doesn't?
Related oven, range & stove problems
Oven Temperature Not Accurate
A drifted temperature sensor or a weak igniter.
See causes & fixesElectric Stove Burner Not Working
A failed surface element or infinite switch.
See causes & fixesGas Burner Won't Light or Keeps Clicking
Moisture or debris on the spark electrode, or a failed igniter switch.
See causes & fixesOven Door Locked
A failed door lock motor or a blown thermal fuse after self-clean.
See causes & fixesOven Won't Turn Off or Overheats
A stuck relay on the control board or a shorted temperature sensor.
See causes & fixesBroiler Not Working
A failed broil element or broil igniter.
See causes & fixes