Codes appear on the display as two letters (OE, IE, UE, dE, LE). The drain pump filter is behind the small door at the bottom left and has an emergency drain hose beside it; most OE calls start there.
LG Front-load washers & WashTower: error codes & what they mean
17 codes explained for WM3400 – WM4200, WM4500 / WM5000 / WM6700 / WM6998 / WM9000, WM1455 / WM1388 models, with the part or problem behind each one. Same-day washing machine repair across Houston.
Models covered
Find the model number on the rating plate. Refrigerators: inside on the left wall above the top shelf. Washers: inside the door rim or on the back. Dryers: inside the door. Dishwashers: left edge of the door. Ranges: behind the storage drawer or on the frame.
- WM3400 – WM4200Mainstream 27-inch front loaders: WM3400CW, WM3500CW, WM3600HWA, WM3700HWA, WM3900HWA, WM4000HWA, WM4200HWA.
- WM4500 / WM5000 / WM6700 / WM6998 / WM9000Mega-capacity and 5.0+ cu ft models, including ezDispense (WM5000HWA, WM6700HBA) and combo WM6998HBA.
- WM1455 / WM1388 (compact)24-inch compact front loaders for condos and closets.
- WKEX / WKGX / WKHC (WashTower)Single-unit washer/dryer towers; the washer section uses these codes.
- WM2xxx / WM3xxx (older)WM2277, WM2050, WM2350, WM3470, WM3570 from 2006–2015.
Example model numbers
- WM3400CW
- WM3600HWA
- WM3900HWA
- WM4000HWA
- WM4200HWA
- WM5000HWA
- WM6700HBA
- WKEX200HWA
LG front-load codes map neatly to parts: OE is the drain path, IE is the inlet, dE is the door lock, LE is the direct-drive motor circuit, UE is balance and PE/FE are the pressure sensor. The direct-drive motor itself rarely fails; LE is far more often a hall sensor connector or a drum overloaded with towels.
On models with ezDispense (WM5000 and newer WM4xxx), the Ed1–Ed5 codes refer to the detergent and softener pumps, which clog with thickened product. OPn means the dispenser drawer isn't closed.
LG front-load washer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
OE | Drain fault | Drain pump filter (behind the lower front cover), pump, hose or standpipe. |
IE | Water inlet fault | Supply valves, hose screens, inlet valve, low pressure. |
UE | Unbalanced load | Redistribute; repeated UE means worn shock absorbers or suspension. |
dE / dE1 / dE2 | Door not closed or door switch fault | Door lock assembly, strike or wiring. |
LE | Motor locked | Overloaded drum, hall sensor, rotor or stator connections. |
FE | Overfill | Inlet valve not closing or pressure sensor. |
PE | Pressure sensor fault | Pressure sensor or blocked air hose. |
tE | Heating / thermistor fault | Thermistor or heater circuit. |
CE | Motor current (short) error | Motor windings, harness or main board. |
EE | EEPROM error | Main control board. |
PF | Power failure during cycle | Restart; check cord and breaker if it repeats. |
SUD / Sd | Excess suds | Less HE detergent; run an extra rinse. |
uS / vS | Vibration sensor fault | Vibration sensor or connection. |
FF | Frozen (water in pump or hoses frozen) | Thaw; relevant in unheated garages during Houston cold snaps. |
OPn | Detergent drawer open (ezDispense) | Close the drawer; drawer sensor if it persists. |
Ed1–Ed5 | ezDispense pump or communication fault | Detergent/softener pump, hardened product in the reservoir, or board. |
nE / nF | Wi-Fi modem error | Modem board; not a washing fault. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
CL | Child lock on | Hold the Child Lock key 3 seconds. |
tCL | Tub clean reminder | Run a Tub Clean cycle. |
Common failures on these models
- Drain pump obstructions and failures (OE)
- Door boot mildew and tears, door lock faults (dE)
- Worn shocks causing UE and loud spin
- Hall sensor and rotor position faults (LE)
- Pressure sensor and air-hose faults (PE / FE)
- Tub bearing roar on 2010–2016 units
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.