Models with a digital display alternate F# and E# (F5 E2). Models with only lights flash the Lid Lock LED when a code is stored; a Wash light alone means long fill (F8 E1), a Spin light alone means long drain (F9 E1). Older Cabrio-style models show two-digit F-codes (F51, F72) and words like LF, Ld, uL and Sd.
Maytag Top-load washers (Bravos, Centennial & current): error codes & what they mean
33 codes explained for MVW4505 / MVW5035 / MVW5430 / MVW6230 / MVW7230 / MVW7232, MVWC, MVWX / MVWB models, with the part or problem behind each one. Same-day washing machine repair across Houston.
Models covered
Find the model number on the rating plate. Washers: under the lid on the top frame. Dryers: inside the door opening. Refrigerators: inside the fresh-food section. Ranges: behind the storage drawer.
- MVW4505 / MVW5035 / MVW5430 / MVW6230 / MVW7230 / MVW7232Current top loaders with Pet Pro, Extra Power and deep fill (MVW4505MW, MVW5430MW, MVW6230HW, MVW7230HW).
- MVWC (Centennial)MVWC200, MVWC360, MVWC415, MVWC465, MVWC565 from 2010–2018.
- MVWX / MVWB (Bravos)Bravos X and Bravos XL: MVWX500, MVWX655, MVWB725, MVWB835, MVWB855, MVWB880 (belt-drive Cabrio platform).
- Older MAV / Atlantis / PerformaMechanical-timer washers with no display codes.
Example model numbers
- MVW4505MW
- MVW5430MW
- MVW6230HW
- MVW7230HW
- MVWC465HW
- MVWX655DW
- MVWB835DW
- MVWB765FW
Maytag's current top loaders and the Centennial line are Whirlpool VMW machines with Maytag styling, so they share the F#E# codes: F5 E2 lid lock, F7 E1 basket speed, F8 E1 long fill, F9 E1 long drain. Bravos and Bravos XL washers are the earlier Cabrio platform with two-digit F-codes (F51, F72) and the words LF, Ld, uL, oL and Sd.
Bravos XL machines are known for a roaring spin as the tub bearing wears; it's a significant repair and we'll quote it honestly against replacement. Lid locks, shifters and drain pumps on all of them are routine same-visit work.
Maytag top-load washer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F0 E2 | Excessive suds | Too much or non-HE detergent; a worn drain path makes it worse. |
F0 E3 | Overloaded | Reduce the load; repeat codes with small loads point at the drive. |
F0 E4 | Rinse water temperature too high | Hoses reversed or thermistor. |
F0 E5 | Unbalanced load | Redistribute; worn suspension rods if it repeats. |
F1 E1 | Main control board failure | Control board after checking console wiring. |
F1 E2 | Motor control error | Motor windings and wiring, then the board. |
F2 E1 | Stuck key | Free the key; UI board if it stays stuck. |
F2 E3 | Control and user interface mismatch | Wrong replacement part installed; corrected. |
F3 E1 | Water level pressure sensor fault | Air hose to the pressure sensor, then the board (sensor is on-board). |
F3 E2 | Inlet water temperature fault | Thermistor, which is part of the inlet valve harness. |
F5 E1 | Lid switch fault (Start pressed with lid open) | Lid lock/switch assembly. |
F5 E2 | Lid lock fault | Debris at the strike, then the lid lock assembly. The single most common code on these washers. |
F5 E3 | Lid unlock fault | Lid lock assembly. |
F5 E4 | Lid not opened between cycles | Lid switch not detecting the lid; lid lock assembly. |
F7 E1 | Basket speed sensor fault | Basket must spin freely; then shifter assembly wiring, then the shifter. |
F7 E5 | Shifter assembly fault | Shifter (mode actuator) assembly. |
F7 E6 | Motor fault | Drive motor or wiring. |
F7 E7 | Motor can't reach target speed | Stuck garment or worn drive components. |
F8 E1 / LF | Not filling or long fill | Faucets, hoses, inlet valves; board if water enters but isn't sensed. |
F8 E3 | Overflow | Inlet valve leaking through, or board. |
F8 E5 | Hot and cold hoses reversed | Swap the hoses; thermistor harness if correct. |
F9 E1 / Ld | Long drain | Drain hose, pump obstruction, pump. |
No match in the main table; check the tables below or text us the code.
Bravos / Cabrio-era codes
| Code | What it means | What usually fixes it |
|---|---|---|
F1 (Cabrio) | Control board fault | Control board. |
F50 / F51 | Motor stalled / rotor position sensor fault | RPS sensor, motor or a jammed basket. |
F52 / F53 / F54 | Motor stop failure / motor overheated / motor overcurrent | Motor, harness or a seized bearing. |
F72 | Basket re-engagement failure | Basket hub or drive block. |
F70 / F71 | Communication error | Harness or boards. |
F80 / F81 / F82 | Lid lock faults | Lid lock assembly. |
F32 / F40 / F41 / F42 | Pressure switch / temperature sensor faults | Pressure switch or thermistor. |
lid / dL / dU | Lid open / lid lock / lid unlock | Lid lock assembly or strike. |
oL / uL | Overloaded / unbalanced | Reduce or redistribute the load; suspension if repeated. |
Sd / SUD | Suds detected | Reduce detergent. |
HC | Hot and cold hoses reversed | Swap the hoses. |
Common failures on these models
- Lid lock failures (F5 E2), the most common code on this platform
- Shifter / actuator faults leaving the washer agitating but not spinning (F7 E1 / F7 E5)
- Drain pump obstructions (F9 E1 / Ld)
- Suspension rod wear (F0 E5 / uL)
- Inlet valve and screens (F8 E1 / LF)
- Tub bearing roar on older Cabrio and Bravos units
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.