Models with a digital display alternate F# and E# (F5 E2). Models with only lights flash the Lid Lock LED when a code is stored; a Wash light alone means long fill (F8 E1), a Spin light alone means long drain (F9 E1). Older Cabrio-style models show two-digit F-codes (F51, F72) and words like LF, Ld, uL and Sd.
Whirlpool Top-load washers (VMW & Cabrio): error codes & what they mean
33 codes explained for WTW4800 – WTW5057, WTW6120 / WTW7120 / WTW8127, WTW6xxx – WTW8xxx models, with the part or problem behind each one. Same-day washing machine repair across Houston.
Models covered
Find the model number on the rating plate. Washers: under the lid or inside the door frame. Dryers: inside the door. Refrigerators: inside the fresh-food compartment on the wall. Dishwashers: on the door edge. Ranges: on the frame behind the door or the drawer.
- WTW4800 – WTW5057 (VMW)Vertical modular washers with impeller or agitator: WTW4816FW, WTW4855HW, WTW4950HW, WTW5000DW, WTW5005KW, WTW5057LW.
- WTW6120 / WTW7120 / WTW8127 (2 in 1)Larger top loaders including the Removable Agitator 2 in 1 models.
- WTW6xxx – WTW8xxx (Cabrio, 2007–2015)Belt-drive Cabrio platform: WTW6400, WTW6600, WTW7300, WTW7600, WTW8200 with the two-digit F-codes.
- Older direct-drive (LSR, LSQ, WTW5xxx 2001–2010)No display codes; faults show as symptoms (won't spin, won't agitate).
Example model numbers
- WTW4816FW
- WTW4855HW
- WTW4950HW
- WTW5000DW
- WTW5057LW
- WTW7120HW
- WTW8127LW
- WTW6600SW2
Whirlpool's vertical modular washer (VMW) platform, sold under Whirlpool, Maytag, Amana, Roper, Admiral and Kenmore 110 names, uses a lid lock, a belt-driven motor and a shifter assembly that switches between agitate and spin. Its codes point at those three parts more than anything else: F5 E2 (lid lock), F7 E1 / F7 E5 (shifter and basket speed) and F9 E1 (drain).
The older Cabrio platform (2007–2015) reports two-digit F-codes read from the diagnostic mode; F51 (rotor position sensor) and F72 (basket re-engagement) were common enough to become shorthand among technicians. Both platforms are inexpensive to repair and worth keeping.
Whirlpool top-load washer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F0 E2 | Excessive suds | Too much or non-HE detergent; a worn drain path makes it worse. |
F0 E3 | Overloaded | Reduce the load; repeat codes with small loads point at the drive. |
F0 E4 | Rinse water temperature too high | Hoses reversed or thermistor. |
F0 E5 | Unbalanced load | Redistribute; worn suspension rods if it repeats. |
F1 E1 | Main control board failure | Control board after checking console wiring. |
F1 E2 | Motor control error | Motor windings and wiring, then the board. |
F2 E1 | Stuck key | Free the key; UI board if it stays stuck. |
F2 E3 | Control and user interface mismatch | Wrong replacement part installed; corrected. |
F3 E1 | Water level pressure sensor fault | Air hose to the pressure sensor, then the board (sensor is on-board). |
F3 E2 | Inlet water temperature fault | Thermistor, which is part of the inlet valve harness. |
F5 E1 | Lid switch fault (Start pressed with lid open) | Lid lock/switch assembly. |
F5 E2 | Lid lock fault | Debris at the strike, then the lid lock assembly. The single most common code on these washers. |
F5 E3 | Lid unlock fault | Lid lock assembly. |
F5 E4 | Lid not opened between cycles | Lid switch not detecting the lid; lid lock assembly. |
F7 E1 | Basket speed sensor fault | Basket must spin freely; then shifter assembly wiring, then the shifter. |
F7 E5 | Shifter assembly fault | Shifter (mode actuator) assembly. |
F7 E6 | Motor fault | Drive motor or wiring. |
F7 E7 | Motor can't reach target speed | Stuck garment or worn drive components. |
F8 E1 / LF | Not filling or long fill | Faucets, hoses, inlet valves; board if water enters but isn't sensed. |
F8 E3 | Overflow | Inlet valve leaking through, or board. |
F8 E5 | Hot and cold hoses reversed | Swap the hoses; thermistor harness if correct. |
F9 E1 / Ld | Long drain | Drain hose, pump obstruction, pump. |
No match in the main table; check the tables below or text us the code.
Cabrio and older codes
| Code | What it means | What usually fixes it |
|---|---|---|
F1 (Cabrio) | Control board fault | Control board. |
F50 / F51 | Motor stalled / rotor position sensor fault | RPS sensor, motor or a jammed basket. |
F52 / F53 / F54 | Motor stop failure / motor overheated / motor overcurrent | Motor, harness or a seized bearing. |
F72 | Basket re-engagement failure | Basket hub or drive block. |
F70 / F71 | Communication error | Harness or boards. |
F80 / F81 / F82 | Lid lock faults | Lid lock assembly. |
F32 / F40 / F41 / F42 | Pressure switch / temperature sensor faults | Pressure switch or thermistor. |
lid / dL / dU | Lid open / lid lock / lid unlock | Lid lock assembly or strike. |
oL / uL | Overloaded / unbalanced | Reduce or redistribute the load; suspension if repeated. |
Sd / SUD | Suds detected | Reduce detergent. |
HC | Hot and cold hoses reversed | Swap the hoses. |
Common failures on these models
- Lid lock failures (F5 E2), the most common code on this platform
- Shifter / actuator faults leaving the washer agitating but not spinning (F7 E1 / F7 E5)
- Drain pump obstructions (F9 E1 / Ld)
- Suspension rod wear (F0 E5 / uL)
- Inlet valve and screens (F8 E1 / LF)
- Tub bearing roar on older Cabrio and Bravos units
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.