Codes display as two characters on the panel; older units use E-codes and words like nF, nd and Ub, newer ones use C-codes (4C, 5C, UC). The lid must be closed and locked before any cycle will run.
Models covered
Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the left wall. Washers: inside the lid or door frame, or on the rear panel. Dryers: inside the door. Dishwashers: on the edge of the door. Ranges: inside the storage drawer or on the frame behind the door.
- WA40 – WA54Current top loaders with ActiveWave or Super Speed: WA45T3400, WA50R5400, WA50B5100, WA52M7750, WA54CG7150.
- WA400 / WA422 / WA456 / WA484 (older)2011–2015 top loaders including those covered by the 2016 top-load recall for lid detachment.
Example model numbers
- WA45T3400AW
- WA50R5400AW
- WA50B5100AW
- WA52M7750AW
- WA54CG7150AV
- WA456DRHDWR
Samsung top loaders are fast and quiet until the suspension wears, and then every spin ends in UC. Suspension rods are the single most common repair on these machines and a same-visit job. The other frequent codes are 4C (no fill), 5C (drain) and dC (lid lock).
Some older WA4xx models were part of a 2016 top-load recall for lids detaching at high spin. If yours is one of them, we'll tell you how to check with Samsung before scheduling.
Samsung top-load washer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
4C / 4E / nF | No water or slow fill | Supply valves, hoses, inlet screens, inlet valve. |
5C / 5E / nd | Drain fault | Drain pump or hose; on top loaders the pump is reached from the back or bottom. |
UC / UE / Ub | Unbalanced load | Redistribute; repeat codes mean worn suspension rods, the most common Samsung top-load repair. |
dC / dE / dL / dS | Lid not closed or lock fault | Lid lock switch or lid striker. |
LC / LE | Leak detected | Hose, pump housing or tub seal; base sensor tripped. |
1C / 1E | Water level sensor fault | Pressure sensor or hose. |
3C / 3E | Motor fault | Motor, rotor position sensor or drive board. |
8C / 8E | Vibration sensor fault | MEMS sensor on the tub. |
AC / AE | Communication error | Harness or control boards. |
bC / bE | Stuck button | Keypad. |
9C / 9E1 | Voltage fault | Supply voltage out of range. |
SUD / 5UD | Excess suds | Reduce detergent. |
tC / tE | Temperature sensor fault | Thermistor. |
No match in the main table; check the tables below or text us the code.
Common failures on these models
- Worn suspension rods causing violent spin and UC codes
- Lid lock switch failures (dC / dL)
- Drain pump debris and failures (5C / nd)
- Water inlet valve and clogged screens (4C / nF)
- Vibration sensor faults (8C) on newer models
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.