Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Problems
  3. Dishwasher Repair
  4. Dishwasher Not Draining
Dishwasher Repair · Houston, TX

Dishwasher not draining?

Standing water at the end of a cycle means the drain path is blocked or the pump has failed. We check the filter, the pump, the hose, the air gap and the disposal connection in that order, and most are cleared or replaced in under an hour.

One visit, 30–60 minutes Same-day in most of Houston 1-year parts, 90-day labor warranty
Quick diagnosis
Most likely cause
A clogged filter, food in the drain pump, or a blocked disposal inlet
Typical repair time
One visit, 30–60 minutes
Service call
$89 diagnostic, credited to the repair

Why it's happening, in order of likelihood

Our technicians test in roughly this order. The numbers reflect how often each cause turns out to be the fault on Houston service calls.

  1. 1

    Clogged filter or sump

    Food, glass and labels collect in the cylindrical filter and the sump below it. Clean monthly in Houston's hard water.

  2. 2

    Drain pump obstruction or failure

    A seed, glass shard or toothpick jams the impeller; or the pump motor fails. The pump hums or does nothing at drain.

  3. 3

    Kinked or clogged drain hose

    A hose that sags behind the cabinet, or that lacks a high loop, fills with sludge or siphons.

  4. 4

    Blocked air gap or disposal inlet

    The air gap on the counter clogs, or the knockout plug in a new garbage disposal was never removed. The second one is a weekly discovery for us.

  5. 5

    Check valve stuck

    A flapper in the drain path sticks and water flows back into the tub after draining.

  6. 6

    Control board

    No power to the pump at the drain step.

Check these before you call

Safe, no-tools checks. If none of them solves it, the next step is a technician.

  • Remove the lower rack and the filter; clean both and look for debris in the sump.
  • If a disposal was recently installed, confirm the knockout plug was removed.
  • Check the drain hose under the sink for a high loop and no kinks.
  • Run the disposal with water; a full disposal blocks the dishwasher drain.

Parts we typically replace

  • Drain pump
  • Drain hose
  • Check valve
  • Filter assembly
  • Control board

Brand-specific notes

  • BoschBosch E24 is a drain fault; E25 points at the pump impeller or cover. The impeller cover under the filter pops off to clear debris.
  • SamsungSamsung 5C or OC codes. The drain pump is accessible from the front on most models.
  • LGLG OE. Check the filter and the drain hose high loop first.
  • WhirlpoolWhirlpool and KitchenAid F8 E1 slow drain; the check valve and pump are the usual causes.
  • FrigidaireFrigidaire i20 / i40: clean the filters first, then the pump.
  • MieleMiele F11: triple filter, drain pump and non-return valve.

Repair or replace?

Always a repair.

What happens on the visit

1

Describe the symptom

Tell us the brand, model and what it's doing. A photo of the model tag helps.

2

We diagnose, you approve

$89 diagnostic, credited to the repair. Flat-rate quote before any work.

3

Fixed, usually that visit

Common parts are on the truck. 1-year parts, 90-day labor warranty on the repair.

Questions about this problem

Is a little water in the bottom of the dishwasher normal?
A small amount in the sump below the filter is normal; it keeps the seals wet. Water covering the tub floor is not.
Why did my dishwasher stop draining after a new disposal?
The knockout plug in the disposal's dishwasher inlet is still in place. It has to be punched out.

Related dishwasher problems

Dishwasher trouble? Same-day help.

Call or text (713) 548-7587 for a same-day appointment anywhere in Greater Houston. $89 diagnostic, credited toward your repair.

Call nowBook online