Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Problems
  3. Washer Repair
  4. Washer Not Draining
Washer Repair · Houston, TX

Washer not draining?

A tub full of water at the end of the cycle means the drain path is blocked or the pump has failed. On most machines it's a sock, a coin or a hair tie in the pump. We clear it or replace the pump in one visit.

One visit, 30–60 minutes Same-day in most of Houston 1-year parts, 90-day labor warranty
Quick diagnosis
Most likely cause
An obstructed or failed drain pump
Typical repair time
One visit, 30–60 minutes
Service call
$89 diagnostic, credited to the repair

Why it's happening, in order of likelihood

Our technicians test in roughly this order. The numbers reflect how often each cause turns out to be the fault on Houston service calls.

  1. 1

    Drain pump obstruction

    Coins, socks, underwire, hair ties and pet hair collect in the pump filter or impeller. The pump hums and moves nothing.

  2. 2

    Failed drain pump

    The pump motor burns out or the impeller breaks. Common on front loaders after 6–8 years.

  3. 3

    Kinked or clogged drain hose

    A hose crushed against the wall or packed with lint, or a standpipe that's clogged.

  4. 4

    Lid switch or door lock

    Many machines won't drain or spin unless the lid or door is confirmed locked.

  5. 5

    Pressure switch or hose

    If the control thinks the tub is empty, it won't run the drain; a clogged pressure hose causes this.

  6. 6

    Control board

    A failed pump relay on the board. Less common.

Check these before you call

Safe, no-tools checks. If none of them solves it, the next step is a technician.

  • Front loaders: open the small access panel at the bottom front, drain into a pan with the emergency hose, then clean the filter.
  • Make sure the drain hose isn't kinked and isn't pushed more than 6–8 inches into the standpipe.
  • Top loaders: check that the lid closes fully and the lid switch clicks.
  • Run a drain/spin cycle and listen for the pump: humming without draining means an obstruction or failed pump.

Parts we typically replace

  • Drain pump
  • Drain hose
  • Lid switch / door lock
  • Pressure switch
  • Control board

Brand-specific notes

  • LGLG shows OE for a drain fault; the pump filter behind the lower front cover is the first stop.
  • SamsungSamsung shows 5C/5E or ND; the debris filter is behind the lower front cover.
  • WhirlpoolWhirlpool Duet and Maytag Maxima front loaders log F21 or F02; the pump sits behind the lower kick panel.
  • BoschBosch compact washers show E18 for a blocked pump or filter.

Repair or replace?

A drain pump is a routine repair on any washer worth keeping.

What happens on the visit

1

Describe the symptom

Tell us the brand, model and what it's doing. A photo of the model tag helps.

2

We diagnose, you approve

$89 diagnostic, credited to the repair. Flat-rate quote before any work.

3

Fixed, usually that visit

Common parts are on the truck. 1-year parts, 90-day labor warranty on the repair.

Questions about this problem

Can I force my washer to drain?
Front loaders have a manual drain hose behind the lower access door. Top loaders can be drained by lowering the drain hose into a bucket.
Why does my washer drain but not spin?
That's a different fault: lid lock, door lock, belt, motor or an unbalanced load.

Related washing machine problems

Washer trouble? Same-day help.

Call or text (713) 548-7587 for a same-day appointment anywhere in Greater Houston. $89 diagnostic, credited toward your repair.

Call nowBook online