- Home
- Problems
- Washer Repair
- Washer Leaking Water
Washer leaking water?
Where and when the water appears tells the story: during fill, during wash, during drain, or only on spin. Door boots, hoses, pump seals, tub seals and dispensers each leak at different moments, and we find the right one.
- Most likely cause
- A torn door boot (front load) or a failed drain pump or hose
- Typical repair time
- One visit, 45–90 minutes
- Service call
- $89 diagnostic, credited to the repair
Why it's happening, in order of likelihood
Our technicians test in roughly this order. The numbers reflect how often each cause turns out to be the fault on Houston service calls.
- 1
Door boot / gasket (front load)
Tears in the bellows, mildew that keeps it from sealing, or debris trapped in the fold. Leaks from the front during wash or spin.
- 2
Drain pump or pump housing
A cracked housing or failed seal leaks at the bottom during drain.
- 3
Fill hoses and inlet valve
Old rubber hoses, loose fittings or a cracked valve body. Leaks behind the machine, sometimes constantly.
- 4
Tub seal and bearing (leaks from underneath during wash/spin)
Water passes a failed tub seal, often with a roaring spin. A significant repair.
- 5
Dispenser overflow / oversudsing
Too much detergent or a clogged dispenser pushes suds and water out the dispenser drawer or the top of the tub. Very common in Houston with HE detergent overdosing.
- 6
Drain hose or standpipe backup
A hose that pops out of the standpipe, or a standpipe that overflows because the house drain is slow.
Check these before you call
Safe, no-tools checks. If none of them solves it, the next step is a technician.
- Note when the leak happens: fill, wash, drain or spin.
- Inspect the door boot fold for tears and debris.
- Check fill hoses and the drain hose connection behind the machine.
- Cut detergent to the manufacturer's amount; run a cycle with no detergent to see if the leak stops.
Parts we typically replace
- Door boot / bellows
- Drain pump
- Fill hoses
- Water inlet valve
- Tub seal & bearings
- Dispenser assembly
Brand-specific notes
- SamsungSamsung front loaders show LC/LE when the base leak sensor trips; the boot or a hose is usually the source.
- LGLG front loaders leak at the door boot and the drain pump housing more than anywhere else.
- WhirlpoolWhirlpool and Maytag top loaders often leak from the tub-to-pump hose or a cracked outer tub nozzle.
Repair or replace?
Boots, hoses and pumps are repairs. A tub seal and bearing job on a budget front loader can approach replacement cost.
What happens on the visit
Describe the symptom
Tell us the brand, model and what it's doing. A photo of the model tag helps.
We diagnose, you approve
$89 diagnostic, credited to the repair. Flat-rate quote before any work.
Fixed, usually that visit
Common parts are on the truck. 1-year parts, 90-day labor warranty on the repair.
Questions about this problem
Should I keep using a washer that leaks a little?
Why does my washer leak only on the spin cycle?
Related washing machine problems
Washer Not Draining
An obstructed or failed drain pump.
See causes & fixesWasher Not Spinning
A failed lid lock, door lock or drive component.
See causes & fixesWasher Won't Start
A failed lid lock or door lock, or a control board.
See causes & fixesWasher Not Filling
Clogged inlet screens or a failed water inlet valve.
See causes & fixesWasher Shaking or Walking
Worn suspension rods (top load) or shock absorbers (front load).
See causes & fixesWasher Making Grinding or Squealing Noise
A worn drive component, bearing or a foreign object in the tub.
See causes & fixes