Current models alternate F# and E# on the display; the older Duet platform shows two-digit codes (F02, F21, F35) and words such as SUD, dL, dU and FH. The drain pump filter is behind the lower kick panel on Duet-era machines and behind a small door on newer ones.
Maytag Front-load washers (Maxima & current): error codes & what they mean
41 codes explained for MHW5630 / MHW6630 / MHW8630, MHW3505 / MHW5500 / MHW8200, MAH / Neptune models, with the part or problem behind each one. Same-day washing machine repair across Houston.
Models covered
Find the model number on the rating plate. Washers: under the lid on the top frame. Dryers: inside the door opening. Refrigerators: inside the fresh-food section. Ranges: behind the storage drawer.
- MHW5630 / MHW6630 / MHW8630Current front loaders with Extra Power and Fresh Hold (MHW5630HW, MHW6630HW, MHW8630HC).
- MHW3505 / MHW5500 / MHW8200 (Maxima)Maxima and Maxima XL (MHW3505FW, MHW5500FW, MHW8200FW, MHWE450WW).
- MAH / Neptune (1997–2007)Neptune front loaders (MAH3000, MAH5500, MAH8700) with their own door-latch and control issues.
Example model numbers
- MHW5630HW
- MHW6630HW
- MHW8630HC
- MHW3505FW
- MHW5500FW
- MHW8200FW
- MHWE450WW
Maytag Maxima and current front loaders are Whirlpool front-load machines and use the same code set: F9 E1 or F21 for drain, F5 E2 or F22 for the door lock, F0 E5 for unbalanced loads. Older Neptune washers predate this system and fail at the door latch wax motor, the door switch and the motor control board.
Maytag front-load washer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F0 E1 / rL | Load detected during Clean Washer cycle | Remove items and rerun. |
F0 E2 | Excessive suds | Reduce HE detergent; clean the pump filter. |
F0 E3 | Overloaded | Reduce the load. |
F0 E5 | Unbalanced load | Redistribute; shocks if it repeats. |
F1 E1 | Main control fault | Main control board. |
F1 E2 | Motor control fault | Motor control / main board or motor. |
F2 E1 | Stuck key | Keypad or UI. |
F2 E3 | UI / control mismatch | Correct part installed. |
F3 E1 | Pressure sensor / water level fault | Pressure sensor or air hose. |
F3 E2 | Water temperature sensor fault | Thermistor. |
F4 E1 | Heater fault | Heating element or relay (models with internal heater). |
F5 E1 | Door switch fault | Door switch or lock. |
F5 E2 | Door lock fault | Door lock assembly. |
F5 E3 | Door unlock fault | Door lock assembly. |
F5 E4 | Door not opened between cycles | Door switch. |
F6 E1 / F6 E2 / F6 E3 | Communication errors between boards | Harness or boards. |
F7 E1 / F7 E6 / F7 E7 | Motor drive fault / motor fault / can't reach speed | Motor, harness, obstruction or board. |
F8 E1 / FH / F20 | No water detected or long fill | Supply, hoses, inlet valves, flow meter. |
F8 E2 | Dispenser system fault | Dispenser motor. |
F8 E3 | Overflow | Inlet valve or pressure sensor. |
F9 E1 / F21 / F02 | Long drain | Pump filter behind the lower panel, drain pump, hose. |
F22 | Door lock fault (older Duet) | Door lock assembly. |
SUD / Sd | Suds detected | Reduce detergent. |
LoC / LC | Control lock on | Hold the lock key 3 seconds. |
Int | Cycle interrupted | Restart. |
dET | Detergent cartridge not detected (Load & Go) | Seat the cartridge. |
PF | Power failure | Restart. |
No match in the main table; check the tables below or text us the code.
Duet-era codes used on older Maxima models
| Code | What it means | What usually fixes it |
|---|---|---|
F05 | Water temperature sensor fault | Thermistor. |
F06 / F25 | Motor tachometer fault | Motor or MCU. |
F07 / F10 / F15 / F31 | Motor control unit faults | MCU. |
F09 / F27 | Overflow | Pressure switch or inlet valve. |
F11 / F28 | Serial communication error | Harness between CCU and MCU, or boards. |
F13 / F30 | Dispenser circuit fault | Dispenser motor. |
F14 | EEPROM error | Central control unit. |
F23 | Heater fault | Heater or relay. |
F24 | Water temperature sensor fault | Thermistor. |
F26 / F29 | Door switch / door unlock fault | Door lock assembly. |
F32 | Pressure switch fault | Pressure switch. |
F33 | Pump drive fault | Drain pump. |
F35 | Analog pressure sensor fault | Pressure sensor; often paired with SUD. |
dL / dU | Door lock / unlock fault | Door lock assembly. |
Common failures on these models
- Drain pump obstructions and failures (F9 E1 / F21 / F02)
- Door lock faults (F5 E2 / F22 / dL)
- Door boot tears and base leaks
- Pressure sensor and suds faults (F3 E1 / F35 / SUD)
- Motor control (MCU) faults on Duet-era machines (F11 / F06)
- Worn shocks causing F0 E5
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.