Codes show on the oven display as F-numbers; cooktops use single digits. LG's own guidance is to press Clear/Off, then reset the breaker for 30 seconds; a code that returns needs a technician.
LG Ranges, wall ovens & cooktops: error codes & what they mean
20 codes explained for LRE / LREL / LSE / LSEL, LRG / LRGL / LSG / LSGL, LDE / LDG / LTE / LTG models, with the part or problem behind each one. Same-day oven, range & stove repair across Houston.
Models covered
Find the model number on the rating plate. Refrigerators: inside on the left wall above the top shelf. Washers: inside the door rim or on the back. Dryers: inside the door. Dishwashers: left edge of the door. Ranges: behind the storage drawer or on the frame.
- LRE / LREL / LSE / LSELElectric freestanding (LRE) and slide-in (LSE) ranges, including ProBake and InstaView (LREL6325F, LSEL6337F, LSE4616ST).
- LRG / LRGL / LSG / LSGLGas freestanding and slide-in ranges (LRGL5825F, LSGL6337F, LSG4513ST).
- LDE / LDG / LTE / LTGDouble-oven ranges and electric/gas cooktops (LDE4415ST, LDG4315ST, LCE3010SB, LTE/LCG).
- LWS / LWD / LWC / LSWSSingle, double and combination wall ovens (LWS3063ST, LWD3063ST, LWC3063ST).
- LSIL / LSIS / LCE (induction)Induction ranges and cooktops (LSIL6336F, LSIS6338F).
Example model numbers
- LREL6325F
- LSEL6337F
- LRGL5825F
- LSGL6337F
- LDE4415ST
- LWS3063ST
- LSIL6336F
- LCE3010SB
LG oven codes are grouped: F1/F2/F4/F5/F16 are temperature sensors, F6/F9/F19 are heating faults, F7/F17 are convection fans, F10/F20 are door locks and F11/F38 are communication. Induction ranges add F33–F46 for the coil sensors, inverter boards and cooling fans.
F9 (oven not heating properly) is the classic no-heat call: a failed bake element or igniter, a relay board that isn't energizing it, or a sensor reading wrong. We test in that order.
LG range & oven error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 / F2 | Upper oven thermistor fault | Oven temperature sensor open or shorted. |
F3 | Touch pad / key fault | Control panel or stuck key. |
F4 / F5 | Lower oven thermistor fault | Lower cavity sensor (double ovens). |
F6 | Upper oven heating error | Element, igniter or relay board. |
F7 / F17 | Convection fan fault | Convection fan motor. |
F8 / F18 | Meat probe fault | Probe or probe jack. |
F9 / F19 | Oven not heating properly | Element, igniter, relay or sensor; the classic no-heat code. |
F10 / F20 | Door lock failure (upper / lower) | Door lock motor or switch. |
F11 | Communication error | Boards or harness. |
F16 | Oven sensor fault | Temperature sensor. |
F21–F25 | Steam sensor fault (steam models) | Steam system sensor. |
F27 | Cooling fan stalled during self-clean | Cooling fan motor. |
F33 / F34 | Induction burner temperature sensor fault | Induction coil sensor. |
F36 / F38 / F42 | Induction transistor, inverter communication or voltage fault | Induction generator board or supply voltage. |
F45 / F46 | Fan fault (induction) | Cooling fan. |
F51–F59 | Griddle sensor or heating fault | Griddle element or sensor. |
F62 / F69 | Sous vide sensor or heating fault | Sous vide module. |
1 / 2 / 3 (cooktop) | Cooktop thermistor fault | Cooktop sensor. |
4 (cooktop) | Water or metal on the touch pads | Clean and dry the surface. |
5 / 6 (cooktop) | Display fault / low voltage | Display board; electrician for voltage. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
H5 | Hot surface indicator | Not a fault. |
PF | Power interrupted | Press Clear/Off. |
Sb / 5b | Sabbath mode | See the manual to exit. |
Common failures on these models
- Oven temperature sensor faults (F1 / F2 / F16)
- Bake element and igniter failures (F6 / F9 / F19)
- Door lock faults after self-clean (F10 / F20)
- Convection fan noise and failure (F7 / F17)
- Induction generator board faults (F36 / F38)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.