Current controls show F# E# pairs (F3 E0). Older electronic range controls show F1–F9. The code often appears during or right after self-clean, when the lock, sensor and thermal fuse are stressed.
Maytag Ranges & Gemini double ovens: error codes & what they mean
16 codes explained for MER6600 – MER8800 / MGR6600 – MGR8800, MET8800 / MGT8800, MES8800 / MGS8800 models, with the part or problem behind each one. Same-day oven, range & stove repair across Houston.
Models covered
Find the model number on the rating plate. Washers: under the lid on the top frame. Dryers: inside the door opening. Refrigerators: inside the fresh-food section. Ranges: behind the storage drawer.
- MER6600 – MER8800 / MGR6600 – MGR8800Electric (MER) and gas (MGR) freestanding ranges (MER6600FZ, MER8800FZ, MGR6600FZ, MGR8800FZ).
- MET8800 / MGT8800 (Gemini)Gemini double-oven ranges, electric and gas.
- MES8800 / MGS8800Slide-in ranges.
- MEW / MMW (wall ovens)Single and double wall ovens.
Example model numbers
- MER6600FZ
- MER8800FZ
- MGR6600FZ
- MGR8800FZ
- MET8800FZ
- MGT8800FZ
- MES8800FZ
Maytag ranges run Whirlpool oven controls and codes: F3 E0 / F3 E1 for the sensor, F5 codes for the door lock, F1 and F2 codes for the control and keypad. Gemini double ovens add a frequent fault that shows no code: one cavity stops heating because a relay on the relay board failed while the elements test fine.
Maytag range & oven error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 E0 / F1 E1 | Control board fault (EEPROM / control failure) | Electronic oven control. |
F2 E0 | Shorted keypad / stuck key | Keypad membrane or control. |
F2 E1 | Keytail disconnected | Ribbon cable reseated or keypad. |
F3 E0 | Oven temperature sensor open | Oven sensor. |
F3 E1 | Oven temperature sensor shorted | Oven sensor or harness. |
F3 E2 / F3 E3 | Oven over-temperature (bake / clean) | Sensor, relay board or control. |
F5 E0 / F5 E1 | Door switch / latch fault | Door lock assembly or switch. |
F5 E2 / F5 E3 | Latch won't lock / won't unlock | Door lock motor or switch. |
F6 E0 / F6 E1 | Communication or relay board fault | Relay board or harness. |
F9 E0 | Door lock circuit fault (older models) | Door lock. |
No match in the main table; check the tables below or text us the code.
Older F1–F9 codes
| Code | What it means | What usually fixes it |
|---|---|---|
F1 | Control board fault | Electronic range control. |
F2 | Oven temperature too high | Sensor or relay. |
F3 / F4 | Oven sensor open / shorted | Oven sensor. |
F5 | Door lock / latch fault | Latch assembly. |
F7 | Stuck key | Keypad. |
F9 | Door latch circuit fault | Latch or lock motor. |
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
PF | Power failure | Reset the clock. |
Common failures on these models
- Relay board faults on Gemini double ovens (one cavity cold)
- Oven sensor faults (F3 E0)
- Door lock faults after self-clean (F5 E1)
- Weak oven igniters on MGR gas ranges
- Bake element burnout on MER electric ranges
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.