Current controls show F# E# pairs (F3 E0). Older electronic range controls show F1–F9. The code often appears during or right after self-clean, when the lock, sensor and thermal fuse are stressed.
JennAir Ranges, wall ovens & downdraft cooktops: error codes & what they mean
16 codes explained for JDRP / JGRP / JDSP / JGSP, JJW / JMW / JDS, JED / JGD / JIC models, with the part or problem behind each one. Same-day oven, range & stove repair across Houston.
Models covered
Find the model number on the rating plate. Cooktops: on the underside, visible from the cabinet. Ranges and wall ovens: on the frame inside the door. Refrigerators: inside the fresh-food section or behind the top grille.
- JDRP / JGRP / JDSP / JGSPPro-style dual-fuel and gas ranges, slide-ins (JDRP436HL, JGRP436HL, JDSP548HL).
- JJW / JMW / JDS (wall ovens)Single, double and combination wall ovens (JJW2430LM, JJW3430LM).
- JED / JGD / JIC (cooktops)Downdraft electric and gas cooktops (JED3430GS, JGD3430GS) and induction (JIC4430XS).
- Older JES / JGS / JDS (1990s–2010)Downdraft ranges with the F1–F9 code set.
Example model numbers
- JDRP436HL
- JGRP436HL
- JDSP548HL
- JJW2430LM
- JJW3430LM
- JED3430GS
- JGD3430GS
- JES9800CAS
JennAir ovens use the Whirlpool oven control codes (F3 E0 sensor, F5 door lock, F1/F2 control and keypad). Downdraft cooktops and ranges add a blower motor that packs with grease and a lift mechanism on telescoping vents, neither of which reports a code.
JennAir range & oven error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 E0 / F1 E1 | Control board fault (EEPROM / control failure) | Electronic oven control. |
F2 E0 | Shorted keypad / stuck key | Keypad membrane or control. |
F2 E1 | Keytail disconnected | Ribbon cable reseated or keypad. |
F3 E0 | Oven temperature sensor open | Oven sensor. |
F3 E1 | Oven temperature sensor shorted | Oven sensor or harness. |
F3 E2 / F3 E3 | Oven over-temperature (bake / clean) | Sensor, relay board or control. |
F5 E0 / F5 E1 | Door switch / latch fault | Door lock assembly or switch. |
F5 E2 / F5 E3 | Latch won't lock / won't unlock | Door lock motor or switch. |
F6 E0 / F6 E1 | Communication or relay board fault | Relay board or harness. |
F9 E0 | Door lock circuit fault (older models) | Door lock. |
No match in the main table; check the tables below or text us the code.
Older F1–F9 codes
| Code | What it means | What usually fixes it |
|---|---|---|
F1 | Control board fault | Electronic range control. |
F2 | Oven temperature too high | Sensor or relay. |
F3 / F4 | Oven sensor open / shorted | Oven sensor. |
F5 | Door lock / latch fault | Latch assembly. |
F7 | Stuck key | Keypad. |
F9 | Door latch circuit fault | Latch or lock motor. |
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
PF | Power failure | Reset the clock. |
Common failures on these models
- Downdraft blower motor failures
- Oven sensor faults (F3 E0)
- Door lock faults after self-clean (F5 E1)
- Relay board faults on double wall ovens
- Spark module faults on gas cooktops
- Induction generator board faults
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.