Codes appear on the oven display as C-xx (sensor, door lock, communication) or, on older models, SE / 5E for a shorted keypad. S-01 is a safety shutoff after many hours at temperature and is not a failure.
Samsung Ranges, slide-ins & wall ovens: error codes & what they mean
10 codes explained for NE59 / NE63 / NE58, NX58 / NX60, NY63 models, with the part or problem behind each one. Same-day oven, range & stove repair across Houston.
Models covered
Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the left wall. Washers: inside the lid or door frame, or on the rear panel. Dryers: inside the door. Dishwashers: on the edge of the door. Ranges: inside the storage drawer or on the frame behind the door.
- NE59 / NE63 / NE58Electric freestanding (NE59) and slide-in (NE63, NE58) ranges, including Flex Duo and air-fry models.
- NX58 / NX60Gas freestanding and slide-in ranges (NX58H5600, NX60T8511, NX60A6511).
- NY63Dual-fuel slide-in ranges.
- NV51 / NQ70Wall ovens and combination microwave-wall ovens.
Example model numbers
- NE59M4320SS
- NE63T8711SS
- NX58H5600SS
- NX60T8511SS
- NY63T8751SS
- NV51K7770DS
Samsung ranges fail at the oven temperature sensor (C-20 family), the door lock after self-clean (C-d1) and the control boards (C-F0, C-F1, C-F2). Gas models also have the usual igniter and spark issues that show no code at all: a weak oven igniter that glows but won't light, or a burner that clicks and won't ignite.
If the display is dead or shows SE / 5E, moisture or a boil-over has usually reached the keypad membrane. Dry it out before assuming the board is gone.
Samsung range & oven error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
C-20 / C-21 / C-22 | Oven temperature sensor fault | Sensor open or shorted; replaced from inside the cavity. |
C-d0 | Button held or stuck | Clean and dry the control panel; keypad if it persists. |
C-d1 | Door lock malfunction | Door lock motor/switch; common after self-clean. |
C-F0 | No communication between main and sub boards | Harness or board. |
C-F1 | EEPROM read/write error | Main control board. |
C-F2 | Touch IC communication problem | Touch control board. |
S-01 | Safety shutoff after a long run | Not a fault: the oven turned itself off after many hours at temperature. |
dC / dE | Divider in wrong position (Flex Duo models) | Insert or remove the divider to match the mode. |
SE / 5E | Shorted key (older models) | Keypad membrane or control. |
Pr E | Preheating | Normal. |
No match in the main table; check the tables below or text us the code.
Common failures on these models
- Oven temperature sensor drift and failure (C-20 / C-21)
- Door lock faults after self-clean (C-d1)
- Weak oven igniters on NX58 gas ranges (no code, slow or no ignition)
- Spark module and igniter switch faults on gas cooktops
- Keypad membrane shorts from spills (SE)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.