Current controls show F# E# pairs (F3 E0). Older electronic range controls show F1–F9. The code often appears during or right after self-clean, when the lock, sensor and thermal fuse are stressed.
- Home
- Brands
- KitchenAid
- Range & Oven
KitchenAid Ranges, wall ovens & cooktops: error codes & what they mean
16 codes explained for KFEG / KFGG / KSEG / KSGG / KSDB / KSDG, KFDC / KFGC, KOSE / KODE / KOCE / KOES / KODT models, with the part or problem behind each one. Same-day oven, range & stove repair across Houston.
Models covered
Find the model number on the rating plate. Dishwashers: left edge of the door. Refrigerators: inside the fresh-food compartment or on the top grille of built-ins. Ranges: on the frame behind the door.
- KFEG / KFGG / KSEG / KSGG / KSDB / KSDGFreestanding and slide-in electric, gas and dual-fuel ranges (KFEG500ESS, KFGG500ESS, KSEG700ESS, KSGG700ESS, KSDB900ESS).
- KFDC / KFGC (Commercial-style)36- and 48-inch commercial-style dual-fuel and gas ranges (KFDC506JSS, KFGC506JSS).
- KOSE / KODE / KOCE / KOES / KODTSingle, double and combination wall ovens (KOSE500ESS, KODE500ESS, KOCE500ESS).
- KCGS / KCES / KICU / KCIGGas, electric and induction cooktops.
Example model numbers
- KFEG500ESS
- KFGG500ESS
- KSEG700ESS
- KSGG700ESS
- KSDB900ESS
- KFDC506JSS
- KOSE500ESS
- KODE500ESS
KitchenAid ovens use Whirlpool's oven control codes: F3 E0 / F3 E1 for the temperature sensor, F5 codes for the door lock, F1 E0 and F2 E0 for control and keypad faults. Commercial-style ranges add convection fan motors, heavy door hinges and dual oven igniters that fail without a code.
KitchenAid range & oven error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 E0 / F1 E1 | Control board fault (EEPROM / control failure) | Electronic oven control. |
F2 E0 | Shorted keypad / stuck key | Keypad membrane or control. |
F2 E1 | Keytail disconnected | Ribbon cable reseated or keypad. |
F3 E0 | Oven temperature sensor open | Oven sensor. |
F3 E1 | Oven temperature sensor shorted | Oven sensor or harness. |
F3 E2 / F3 E3 | Oven over-temperature (bake / clean) | Sensor, relay board or control. |
F5 E0 / F5 E1 | Door switch / latch fault | Door lock assembly or switch. |
F5 E2 / F5 E3 | Latch won't lock / won't unlock | Door lock motor or switch. |
F6 E0 / F6 E1 | Communication or relay board fault | Relay board or harness. |
F9 E0 | Door lock circuit fault (older models) | Door lock. |
No match in the main table; check the tables below or text us the code.
Older F1–F9 codes
| Code | What it means | What usually fixes it |
|---|---|---|
F1 | Control board fault | Electronic range control. |
F2 | Oven temperature too high | Sensor or relay. |
F3 / F4 | Oven sensor open / shorted | Oven sensor. |
F5 | Door lock / latch fault | Latch assembly. |
F7 | Stuck key | Keypad. |
F9 | Door latch circuit fault | Latch or lock motor. |
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
PF | Power failure | Reset the clock. |
Common failures on these models
- Oven sensor faults (F3 E0 / F3 E1)
- Door lock faults after self-clean (F5 E1 / F5 E2)
- Convection fan motor noise and failure
- Weak igniters on gas ranges and rangetops
- Spark module and igniter switch faults on cooktops
- Relay board faults on double wall ovens
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.