Codes appear on the front or top-control display; on hidden-control models the cycle lights blink in a pattern. LC/LE is the leak sensor in the base pan and stops the dishwasher until the pan is dry and the leak is fixed.
Models covered
Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the left wall. Washers: inside the lid or door frame, or on the rear panel. Dryers: inside the door. Dishwashers: on the edge of the door. Ranges: inside the storage drawer or on the frame behind the door.
- DW80 seriesStandard 24-inch: DW80R5060, DW80R9950 (Linear Wash), DW80K7050, DW80M9960 (WaterWall), DW80B7070, DW80CG5450.
- DW50 series18-inch compact (DW50R4060, DW50T6060) for townhomes and bars.
- DMT / DMR (older)2009–2013 models such as DMT800 and DMR78.
Example model numbers
- DW80R5060US
- DW80R9950US
- DW80K7050US
- DW80M9960US
- DW80B7070US
- DW50R4060BB
Samsung dishwashers tell you exactly which system failed: 4C is fill, 5C is drain, 3C is the wash pump, HC is the heater and LC is the leak sensor. Most are same-visit repairs with parts from the truck.
LC deserves a technician rather than a tilt-and-dry. The base-pan sensor tripped because water got there, usually from the door gasket, a sump seal or a cracked hose, and until that is fixed the code returns.
Samsung dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
1E / 1C | Clogged filter | Clean the cylindrical filter and sump; sensor-based on newer models. |
3C / 3E | Wash pump operation fault | Circulation motor or its harness; debris in the impeller. |
4C / 4E | Water supply fault | Supply valve, inlet valve, or low pressure. |
5C / 5E | Drain fault | Drain pump, check valve, hose or disposal knockout. |
7E | WaterWall reflector fault | Reflector motor or track blocked (WaterWall models). |
9E | Low water level | Fill issue or leak; often the inlet valve or a float. |
AC / AE | Communication error | Main-to-UI harness or board. |
bE / bC | Stuck button | Keypad. |
CE | Communication error (older models) | Boards or harness. |
HC / HE / HE1 | Heater fault / high temperature | Heating element or thermistor. |
LC / LE | Leak detected | Water in the base pan: gasket, sump seal, hoses. |
OC / OE | Overflow | Inlet valve not closing or level sensor. |
PC / PE | Half-load function fault | Distribution valve on half-load models. |
tC / tE | Temperature sensor fault | Thermistor. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
Delay start / child lock indicators | Not faults | Hold the lock key 3 seconds to release. |
Common failures on these models
- Leak sensor trips (LC) from door gaskets and sump seals
- Drain pump and check valve faults (5C)
- WaterWall reflector motor faults (7E) on DW80H and DW80K models
- Wash motor faults (3C) on older units
- Heater and thermistor faults (HC / tC)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.