Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. LG
  4. Dryer
LG · Dryer Repair · error codes

LG Electric & gas dryers: error codes & what they mean

12 codes explained for DLEX3700 – DLEX4500, DLGX3701 – DLGX4501, DLE7xxx / DLG7xxx / DLE3400 models, with the part or problem behind each one. Same-day dryer repair across Houston.

5 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Refrigerators: inside on the left wall above the top shelf. Washers: inside the door rim or on the back. Dryers: inside the door. Dishwashers: left edge of the door. Ranges: behind the storage drawer or on the frame.

  • DLEX3700 – DLEX4500Electric dryers with Flow Sense and TurboSteam (DLEX3700W, DLEX3900W, DLEX4000W, DLEX4200W, DLEX4500B).
  • DLGX3701 – DLGX4501Gas versions of the same platform.
  • DLE7xxx / DLG7xxx / DLE3400Mid-range electric and gas dryers (DLE7300WE, DLG7301WE, DLE3400W).
  • DLHC / WKEX (WashTower dryer)Ventless heat-pump dryers and the dryer half of WashTower.
  • DLE2xxx / DLG2xxx (older)DLE2516W, DLE2140W and relatives.

Example model numbers

  • DLEX3700W
  • DLEX3900W
  • DLEX4000W
  • DLEX4200W
  • DLGX3701W
  • DLE7300WE
  • DLHC1455W
How codes are displayed

Codes appear on the display. Flow Sense (d80, d90, d95) is the dryer measuring airflow restriction and is a vent problem, not a dryer failure. nP and PS are power-supply codes from the 240V connection.

LG dryers are honest about airflow: d80 means your vent is roughly 80% blocked, and the dryer will take forever until the duct is cleared. In two-story Houston homes with long vent runs this is the single most common LG dryer code we see, and clearing the vent at the dryer and the wall often fixes a 'broken' dryer.

nP and PS are the other frequent ones: the dryer tumbles but won't heat because one leg of 240V is missing (nP) or the cord was wired wrong at the terminal block (PS). Check the double breaker first.

LG dryer error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
d75 / d80 / d90 / d95Exhaust duct restricted 75–95% (Flow Sense)Clear the lint screen, transition hose and vent; on gas dryers d80 can also mean no gas supply.
nPNo current at the heaterOne leg of 240V missing: breaker, cord or outlet. An electrician if the dryer side checks out.
PSPower cord wired incorrectly or improper voltageTerminal block wiring (white/red reversed) or outlet.
dEDoor not fully closedDoor switch, strike, or lint filter not seated.
E13Drain hose kinked/clogged or sump frozen (condensing hybrid dryers)Straighten or clear the drain hose.
F0 / Insert FilterLint filter not seatedReinsert the filter.
HSHumidity sensor faultClean the sensor bars; replace the sensor if it persists.
PFPower failureFactory reset: unplug, hold Start/Pause 5 seconds, restore power.
tE1 / tE3Thermistor faultTemperature sensor or harness.
tE2Thermistor fault in cold conditions or steam cyclesClear vents of cold-air backflow; sensor if it returns.
gAS (shown as 9A5)No gas reaching a gas dryerGas valve open? Then igniter, coils or the supply.
AddSteam feeder needs waterFill the steam reservoir with tap water.

Messages that aren't faults

Things the display shows that don't mean a part has failed.

CodeWhat it meansWhat usually fixes it
CLChild lockHold Child Lock 3 seconds.
Clean FilterReminder before each loadClean the lint filter.

Common failures on these models

  • Restricted vents (d80 / d90 / d95) and blown thermal fuses
  • Heating element failures on electric models
  • Igniter and gas valve coil faults on DLGX gas dryers
  • Idler pulley and roller noise
  • Moisture sensor film (HS) causing wrong auto-dry times

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

LG dryer questions

My LG dryer shows d90. Do I need a repair?
You need the vent cleared. We check airflow at the dryer and the exterior vent during a visit; long roof or multi-story runs may need a dedicated vent cleaning service.
What does nP mean?
No power at the heater: usually one lost leg of the 240V supply. Reset the double breaker fully; if it trips again, call an electrician.
Do you repair every LG dryer model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under LG's factory warranty, call the manufacturer first.

Related dryer problems

LG showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online