Codes show on the display or as blinking cycle lights. AE / E1 / FE indicate water in the base or overfilling; OE is drain; IE is fill. Holding Start for 3 seconds forces a drain on most models.
Models covered
Find the model number on the rating plate. Refrigerators: inside on the left wall above the top shelf. Washers: inside the door rim or on the back. Dryers: inside the door. Dishwashers: left edge of the door. Ranges: behind the storage drawer or on the frame.
- LDF / LDFN / LDFCFront-control QuadWash (LDF5545ST, LDFN4542S, LDFC2423V).
- LDT / LDTS / LDTHTop-control QuadWash with TrueSteam (LDT5678ST, LDTS5552S, LDTH7972S).
- LDP / LDPM / LDPSTop-control with Dynamic Dry and QuadWash Pro (LDP6797ST, LDPM6762S, LDPS6762S).
- LDS / LDF (older)LDS5540, LDF7774, LDF7551 and relatives from 2010–2016.
Example model numbers
- LDF5545ST
- LDFN4542S
- LDT5678ST
- LDTS5552S
- LDP6797ST
- LDPM6762S
- LDTH7972S
LG dishwashers run quiet and report faults clearly. The three codes that matter most are AE/E1 (the base pan has water in it), OE (the tub isn't draining) and nE (the Vario pump impeller is blocked, often by a dropped utensil).
QuadWash models have a fine filter under the lower spray arm that Houston's hard water and food debris clog; cleaning it monthly prevents a share of OE calls.
LG dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
AE / E1 / FE | Leak or overfill detected | Water in the base: gasket, sump seal, hose; also oversudsing or an unlevel unit. |
IE | Water inlet fault | Supply valve, hose, inlet valve. |
OE | Drain fault | Filter, drain hose height, drain pump, disposal connection. |
tE | Temperature sensor fault | Thermistor. |
HE | Heater fault | Heating element or relay. |
LE | Wash motor fault | Circulation motor or harness. |
PE | Water level sensor fault (older models) | Pressure sensor. |
bE | Bubble (suds) error | Dish soap or too much detergent; sensor if it repeats without suds. |
nE | Vario pump fault | Impeller blocked or dishes touching it; pump if it persists. |
F31 | Heat Dry fan fault | Drying fan motor. |
F35 | Heat Dry temperature fault | Heat dry heater or sensor. |
F37 | Auto-open door fault | Door auto-open mechanism obstructed or failed. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
CL | Control lock | Hold Half Load and Energy Saver for 3 seconds. |
Common failures on these models
- Leak sensor trips (AE / E1) from door gaskets and sump seals
- Drain faults (OE) from filters and hose height
- Vario pump blockages (nE)
- Heater faults (HE) leaving dishes wet and cold
- Door latch and auto-open faults (F37)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.