LG-built Kenmores use LG codes: OE, IE, UE, dE, LE, FE, PE, tE and SUD on washers; d80/d90/d95, tE1, PS, nP and dE on dryers. The pump filter on the front loaders is behind the lower-left door.
Kenmore 796-series Elite washers & dryers (LG-built): error codes & what they mean
31 codes explained for 796.4xxxx, 796.2xxxx / 796.3xxxx, 796.8xxxx / 796.9xxxx / 796.7xxxx models, with the part or problem behind each one. Same-day washing machine repair across Houston.
Models covered
Find the model number on the rating plate. Same places as the manufacturer that built it: under the lid or inside the door for laundry, inside the fresh-food section for refrigerators, on the door edge for dishwashers. The model number starts with the three-digit manufacturer prefix.
- 796.4xxxx (front-load washers)Elite front loaders built by LG (796.41002, 796.41072, 796.41382, 796.41582, 796.41722).
- 796.2xxxx / 796.3xxxx (top-load washers)Elite top loaders built by LG (796.29272, 796.31512, 796.31552).
- 796.8xxxx / 796.9xxxx / 796.7xxxx (dryers)Elite electric and gas dryers built by LG (796.81072, 796.81382, 796.91382, 796.71512).
Example model numbers
- 796.41002610
- 796.41382410
- 796.41582411
- 796.29272000
- 796.31512210
- 796.81382410
- 796.91382410
Kenmore Elite laundry with a 796 prefix was built by LG and behaves exactly like the LG models it mirrors: direct-drive washers with OE drain and LE motor codes, and dryers with Flow Sense vent codes. We bring LG parts to these calls.
Kenmore 796 series elite laundry error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
OE | Drain fault | Drain pump filter (behind the lower front cover), pump, hose or standpipe. |
IE | Water inlet fault | Supply valves, hose screens, inlet valve, low pressure. |
UE | Unbalanced load | Redistribute; repeated UE means worn shock absorbers or suspension. |
dE / dE1 / dE2 | Door not closed or door switch fault | Door lock assembly, strike or wiring. |
LE | Motor locked | Overloaded drum, hall sensor, rotor or stator connections. |
FE | Overfill | Inlet valve not closing or pressure sensor. |
PE | Pressure sensor fault | Pressure sensor or blocked air hose. |
tE | Heating / thermistor fault | Thermistor or heater circuit. |
CE | Motor current (short) error | Motor windings, harness or main board. |
EE | EEPROM error | Main control board. |
PF | Power failure during cycle | Restart; check cord and breaker if it repeats. |
SUD / Sd | Excess suds | Less HE detergent; run an extra rinse. |
uS / vS | Vibration sensor fault | Vibration sensor or connection. |
FF | Frozen (water in pump or hoses frozen) | Thaw; relevant in unheated garages during Houston cold snaps. |
OPn | Detergent drawer open (ezDispense) | Close the drawer; drawer sensor if it persists. |
Ed1–Ed5 | ezDispense pump or communication fault | Detergent/softener pump, hardened product in the reservoir, or board. |
nE / nF | Wi-Fi modem error | Modem board; not a washing fault. |
No match in the main table; check the tables below or text us the code.
Dryer codes (LG platform)
| Code | What it means | What usually fixes it |
|---|---|---|
d75 / d80 / d90 / d95 | Exhaust duct restricted 75–95% (Flow Sense) | Clear the lint screen, transition hose and vent; on gas dryers d80 can also mean no gas supply. |
nP | No current at the heater | One leg of 240V missing: breaker, cord or outlet. An electrician if the dryer side checks out. |
PS | Power cord wired incorrectly or improper voltage | Terminal block wiring (white/red reversed) or outlet. |
dE | Door not fully closed | Door switch, strike, or lint filter not seated. |
E13 | Drain hose kinked/clogged or sump frozen (condensing hybrid dryers) | Straighten or clear the drain hose. |
F0 / Insert Filter | Lint filter not seated | Reinsert the filter. |
HS | Humidity sensor fault | Clean the sensor bars; replace the sensor if it persists. |
PF | Power failure | Factory reset: unplug, hold Start/Pause 5 seconds, restore power. |
tE1 / tE3 | Thermistor fault | Temperature sensor or harness. |
tE2 | Thermistor fault in cold conditions or steam cycles | Clear vents of cold-air backflow; sensor if it returns. |
gAS (shown as 9A5) | No gas reaching a gas dryer | Gas valve open? Then igniter, coils or the supply. |
Add | Steam feeder needs water | Fill the steam reservoir with tap water. |
CL | Child lock | Hold Child Lock 3 seconds. |
Clean Filter | Reminder before each load | Clean the lint filter. |
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
CL | Child lock on | Hold the Child Lock key 3 seconds. |
tCL | Tub clean reminder | Run a Tub Clean cycle. |
Common failures on these models
- Drain pump obstructions (OE)
- Door boot and door lock faults (dE)
- Hall sensor / rotor faults (LE)
- Worn shocks (UE)
- Vent restriction codes on dryers (d80 / d90 / d95)
- Heating element failures on electric dryers
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.