Newer models flash the Clean or Complete light in F#E# sequences or show the code on the display. 2005–2012 models report 'function codes' as blinks of the Clean light: count the blinks, pause, count again (7-1 means seven blinks, pause, one blink).
Kenmore 665-series dishwashers (Whirlpool-built): error codes & what they mean
26 codes explained for 665.13xxx / 665.14xxx / 665.15xxx, 665.17xxx / 665.16xxx models, with the part or problem behind each one. Same-day dishwasher repair across Houston.
Models covered
Find the model number on the rating plate. Same places as the manufacturer that built it: under the lid or inside the door for laundry, inside the fresh-food section for refrigerators, on the door edge for dishwashers. The model number starts with the three-digit manufacturer prefix.
- 665.13xxx / 665.14xxx / 665.15xxxCurrent and recent Whirlpool-platform dishwashers (665.13203, 665.13543, 665.14573, 665.15113).
- 665.17xxx / 665.16xxx (2005–2012)Elite and Ultra Wash models with Clean-light blink codes (665.17033, 665.16033).
Example model numbers
- 665.13203N410
- 665.13543N410
- 665.14573N610
- 665.15113K217
- 665.17033401
- 665.16033401
A 665-prefix Kenmore dishwasher was built by Whirlpool and uses the Whirlpool dishwasher code set: F8 E1 slow drain, F6 E1 no fill, F7 E1 heater, F2 E2 user interface, with older units reporting through Clean-light blinks.
Kenmore 665 series dishwashers error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 E1 / F1 E2 | Thermistor or optical water indicator (OWI) fault | Thermistor/OWI sensor in the sump. |
F2 E1 | Stuck key | Keypad. |
F2 E2 | User interface fault or mismatch | UI board. |
F3 E1 / F3 E2 | Thermistor / OWI fault | Sensor or dirty OWI lens. |
F4 E1 | Wash motor fault / drain not completed before fill | Circulation motor or drain issue. |
F5 E1 / F5 E2 | Door switch open / door not latched | Door latch or switch. |
F6 E1 | No water detected | Supply valve, inlet valve, float. |
F6 E2 | Water inlet valve electrical fault | Inlet valve or wiring. |
F6 E3 | Suds or air in pump | Wrong detergent or a fill problem. |
F6 E4 | Float switch open | Overfill float stuck or a leak into the sump area. |
F6 E6 / F6 E7 | Incoming water too hot / flow meter fault | Water heater setting or flow meter. |
F7 E1 | Heating fault | Heating element, thermal fuse or relay. |
F7 E2 | Heater stuck on | Control board relay. |
F8 E1 | Slow drain | Check valve, drain path, pump. |
F8 E2 | Drain pump electrical fault | Drain pump or wiring. |
F9 E1 / F9 E2 | Drain pump fault / stuck on | Drain pump or control relay. |
FA E1 | Dispenser fault | Detergent dispenser. |
No match in the main table; check the tables below or text us the code.
Clean-light blink codes (older 665 models)
| Code | What it means | What usually fixes it |
|---|---|---|
1-1 | Stuck relay on control board | Control board. |
2-1 | Stuck key | Keypad. |
3-1 / 3-2 | Thermistor / OWI fault | Sensor. |
5-1 / 5-2 | Door switch open / door not closed | Latch or switch. |
6-1 / 6-2 / 6-4 | No fill / inlet valve electrical / float switch open | Supply, valve or float. |
7-1 / 7-2 | Heater not heating / heater stuck on | Element, fuse, board. Seven blinks of the Clean light is the classic heater fault. |
8-1 / 8-2 | Slow drain / drain pump electrical | Drain path or pump. |
9-1 | Diverter motor position fault | Diverter motor. |
10-1 | Dispenser fault | Dispenser. |
Common failures on these models
- Slow drain from check valves and chopper jams (F8 E1 / 8-1)
- Heater and thermal fuse faults (F7 E1 / 7-1)
- Dark panels from board thermal fuses on older units
- Door latch faults (F5 E1)
- Wash motor failures (F4 E1)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.