Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Kenmore
  4. 401 Series Laundry
Kenmore · Washer Repair · error codes

Kenmore 401-series washers & dryers (Samsung-built): error codes & what they mean

39 codes explained for 401.4xxxx, 401.2xxxx, 401.8xxxx / 401.9xxxx models, with the part or problem behind each one. Same-day washing machine repair across Houston.

3 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Same places as the manufacturer that built it: under the lid or inside the door for laundry, inside the fresh-food section for refrigerators, on the door edge for dishwashers. The model number starts with the three-digit manufacturer prefix.

  • 401.4xxxx (front-load washers)Samsung-built Kenmore front loaders (401.41002, 401.41022, 401.41072).
  • 401.2xxxx (top-load washers)Samsung-built top loaders (401.29002, 401.29022).
  • 401.8xxxx / 401.9xxxx (dryers)Samsung-built electric and gas dryers (401.81002, 401.91002).

Example model numbers

  • 401.41002
  • 401.41072
  • 401.29002
  • 401.29022
  • 401.81002
  • 401.91002
How codes are displayed

Samsung-built Kenmores use Samsung codes: 4E/4C, 5E/5C, UE/UC, dE/dC, LE/LC and SUD on washers; tS, HE, dE and 9E1 on dryers.

A 401-prefix Kenmore was built by Samsung and uses Samsung parts and codes. The front loaders share Samsung's drain (5E), door (dE) and leak (LE) codes; the top loaders have Samsung's suspension-rod wear pattern (UE); the dryers show Samsung heat codes (HE, tS).

Kenmore 401 series laundry error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
4C / 4ENo water supplySupply valves, kinked hoses, clogged inlet screens, failed inlet valve or low pressure.
5C / 5E / ndDrain faultDebris filter behind the lower cover, drain pump, hose or standpipe.
3C / 3EMotor drive faultMotor, hall sensor or main board; also triggered by an overloaded drum.
UC / UE / UrUnbalanced load or control can't balance itRedistribute the load; repeat codes mean shocks or suspension.
dC / dE / dC1 / dE1Door not closed or lockingDoor latch, lock assembly or wiring. On AddWash models dC3 points at the small door.
LC / LE / LC1Leak detected in the baseDoor boot, hose, dispenser overflow or pump seal; the leak sensor in the base pan tripped.
OC / OEOverflow / water level too highInlet valve not closing or pressure sensor fault.
HC / HEWater heater fault (hot water models)Heater element or thermistor on models with internal heating.
tC / tE / tC1Temperature sensor faultThermistor open or shorted.
1C / 1EWater level (pressure) sensor faultPressure sensor or its air hose.
8C / 8EVibration (MEMS) sensor faultVibration sensor or its connector.
AC / AE / AC6Communication error between boardsHarness between main board and user interface, or a failed board.
bC / bE / bE2Stuck buttonKeypad or UI board.
9C / 9E1Voltage out of rangeHousehold voltage low or high; check the outlet and breaker before suspecting the board.
SUD / 5UD / SdExcess sudsToo much or non-HE detergent; pump filter cleaned.
HotWater too hot to open doorWait for the drum to cool; not a fault.

Top-load washer codes

CodeWhat it meansWhat usually fixes it
4C / 4E / nFNo water or slow fillSupply valves, hoses, inlet screens, inlet valve.
5C / 5E / ndDrain faultDrain pump or hose; on top loaders the pump is reached from the back or bottom.
UC / UE / UbUnbalanced loadRedistribute; repeat codes mean worn suspension rods, the most common Samsung top-load repair.
dC / dE / dL / dSLid not closed or lock faultLid lock switch or lid striker.
LC / LELeak detectedHose, pump housing or tub seal; base sensor tripped.
1C / 1EWater level sensor faultPressure sensor or hose.
3C / 3EMotor faultMotor, rotor position sensor or drive board.
8C / 8EVibration sensor faultMEMS sensor on the tub.
AC / AECommunication errorHarness or control boards.
bC / bEStuck buttonKeypad.
9C / 9E1Voltage faultSupply voltage out of range.
SUD / 5UDExcess sudsReduce detergent.
tC / tETemperature sensor faultThermistor.

Dryer codes

CodeWhat it meansWhat usually fixes it
tS / tE / tC / tE5Thermistor faultTemperature sensor open or shorted; often after a restricted vent overheated it.
HC / HEHeating fault (electric)Heating element, thermal cutoff or thermistor; check the 240V breaker first.
hEHeating fault (gas)Igniter, flame sensor or gas valve coils.
dC / dE / dODoor open or door switch faultDoor switch or strike.
bC / bEStuck buttonKeypad or UI board.
9C1 / 9E1Voltage out of rangeSupply voltage; one lost 240V leg is common.
FC / FEPower frequency errorSupply frequency out of range; usually a generator or wiring issue.
AC / AECommunication errorBoard harness or failed board.
3C / 3EMotor faultDrive motor or its relay; a seized drum roller can trigger it.
Clg / Cg / Clean filterLint filter reminder or vent restriction indicatorClean the filter; on Vent Sensor models a lit vent icon means restricted airflow.

Common failures on these models

  • Drain pump obstructions (5E / 5C)
  • Suspension rod wear on top loaders (UE)
  • Door lock and boot faults on front loaders (dE / LE)
  • Heating element and thermistor faults on dryers (HE / tS)
  • Idler pulley noise on dryers

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Kenmore 401 series laundry questions

Can you get parts for a Samsung-built Kenmore?
Yes. We order by the Samsung part number, so availability is the same as for Samsung.
Do you repair every Kenmore 401 series laundry model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Kenmore's factory warranty, call the manufacturer first.

Related washing machine problems

Kenmore showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online