Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Kenmore
  4. 253 / 417 / 587 / 790 Series
Kenmore · Refrigerator Repair · error codes

Kenmore 253, 417, 587 & 790 series (Frigidaire-built): error codes & what they mean

84 codes explained for 253.xxxxx, 417.xxxxx, 587.xxxxx models, with the part or problem behind each one. Same-day refrigerator repair across Houston.

4 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Same places as the manufacturer that built it: under the lid or inside the door for laundry, inside the fresh-food section for refrigerators, on the door edge for dishwashers. The model number starts with the three-digit manufacturer prefix.

  • 253.xxxxx (refrigerators & freezers)Frigidaire-built side-by-side, top-freezer, French door refrigerators and upright/chest freezers (253.70313, 253.44393, 253.28432).
  • 417.xxxxx (washers & dryers)Frigidaire Affinity-based front-load washers and dryers (417.41042, 417.81042, 417.44052).
  • 587.xxxxx (dishwashers)Frigidaire-built dishwashers (587.15102, 587.16153).
  • 790.xxxxx (ranges & wall ovens)Frigidaire-built electric and gas ranges and wall ovens (790.92303, 790.94042, 790.74033).

Example model numbers

  • 253.70313211
  • 253.44393401
  • 417.41042100
  • 417.81042000
  • 587.15102800
  • 790.92303010
  • 790.74033310
How codes are displayed

Frigidaire-built Kenmores use Frigidaire's codes: SY EF / SY CE / H1 on refrigerators, E-codes on 417 laundry (E20, E41, E64), i-codes on 587 dishwashers (i20, i30) and F-codes on 790 ranges (F10, F30, F90).

Four Kenmore prefixes point to Frigidaire (Electrolux): 253 refrigerators and freezers, 417 laundry, 587 dishwashers and 790 ranges. Each uses Frigidaire's code system and takes Frigidaire parts, which are inexpensive and plentiful.

The tables below start with the 253 refrigerators and freezers, then cover 417 laundry, 587 dishwashers and 790 ranges.

Kenmore 253 / 417 / 587 / 790 series error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
SY EFEvaporator fan circuit failureEvaporator fan motor or harness; iced fan from a defrost fault.
SY CECommunication error between boardsHarness or control boards.
SY CFCommunication failure at power-upUser interface or main board.
H1 / HIHigh temperature alarmCheck cooling; often appears after an outage or a door left open.
OP (with zone)Sensor openFreezer or refrigerator thermistor.
SH (with zone)Sensor shortedThermistor or harness.
PFPower failureInformational.

417 washer codes (Affinity platform)

CodeWhat it meansWhat usually fixes it
E10Water not entering / low pressureSupply, hoses, inlet valve.
E11Fill time too longInlet valve, screens, pressure.
E13Water leak in tub or air leak in air bellLeak or pressure hose.
E20 / E21Water not pumping out fast enoughDrain pump obstruction, hose, pump.
E23 / E24Drain pump relay faultControl board.
E31Pressure sensor not communicatingPressure sensor or board.
E35Pressure sensor indicates overfillInlet valve or sensor.
E41Control thinks door switch is openDoor lock assembly.
E42Door remains locked at end of cycleDoor lock.
E43–E48Door lock assembly or control faultsDoor lock or board.
E52Bad signal from tacho generatorMotor tach or harness.
E55Motor overheatingMotor or overload.
E56 / E57 / E58High motor current / inverter currentMotor, inverter or harness.
E59No tacho signal for 3 secondsMotor tach.
E5A / E5B / E5CHeat sink too hot (motor control)Motor control board.
E5D / E5E / E5FCommunication problem with motor controlHarness or boards.
E66Heater relay failureControl board.
E67Input voltage incorrect on boardBoard or supply.
E68Current leakage to ground on heaterHeater or fuse.
E71 / E74 / E75 / E76Water temperature sensor (NTC) faultsThermistor or harness.
E82 / E83 / E93 / E94Console or control configuration faultsUI or control board.
E91 / E95 / E97 / E98Communication errors between UI and controlHarness or boards.
EB1 / EB2 / EB3Line frequency or voltage out of limitsHousehold supply.
EF1Clogged drain pumpPump cleaned or replaced.
EF2Too much detergentReduce detergent.
EF5Water temperature too highThermistor or heater relay.

417 dryer codes

CodeWhat it meansWhat usually fixes it
E31 / E32Moisture (contact) sensor frequency too high / too lowSensor bars, wiring; board if clean.
E42Door sensing failureControl board.
E51Motor relay failureControl board.
E52Motor stopped or not startingDrum friction, voltage, motor thermal protector, motor.
E53Motor centrifugal switch failureMotor.
E54Motor sensing failureControl board.
E61Heater relay failureControl board.
E63Heater shorted to groundHeating element.
E64Heater open circuitHeating element; the most common Frigidaire/Electrolux dryer code.
E65High-limit thermostat tripped repeatedlyVent restriction first, then limiter and high-limit.
E66Thermal limiter openThermal limiter; check for overheating cause.
E67Heater sensing failureControl board.
E71 / E72Outlet thermistor open / shortedOutlet thermistor.
E73 / E74Inlet thermistor open / shortedInlet thermistor.
E91 / E92 / E93 / E94 / E97Communication, protocol or configuration errorsBoards or console.
EA1 / EA2 / EA3Line frequency / voltage too high / too lowHousehold supply.
EA4Improper home wiringTerminal block L1-N-L2.
EA5Voltage sensing failureControl board.
EF1Vent blockedClear the vent; check thermistors.
EF3Maximum cycle time exceededVent, moisture sensor, thermistors.
EF8Key stuckConsole.

587 dishwasher codes

CodeWhat it meansWhat usually fixes it
i10Water level too low / not fillingSupply valve, hose, inlet valve.
i20 / i40 / iF0Drain restricted or filters cloggedFilters, drain hose, pump.
i30Leak into the baseFind the leak: gasket, sump seal, hoses.
i50Wash motor or drain faultReset; circulation or drain pump.
i60Water heating system errorHeater or thermistor.
iC0Electronic control faultPower reset; control board if it returns.
UOVent plunger openVent assembly or wiring.
UFVent fan wrong speedVent fan or board.
ERTouchpad failure / stuck keyKeypad.
CEConfiguration errorControl board.
tuTurbidity sensor failureTurbidity sensor.
hsHall sensor errorWash motor sensor.
HOWater temperature too lowIncoming hot water or heater.
rA / RE / RFRinse aid switch faultsDispenser assembly.
PFPower failureInformational.
CLDoor not latchedClose firmly.
LORinse aid lowRefill.

790 range codes

CodeWhat it meansWhat usually fixes it
F10Runaway temperatureOven sensor or relay board; address promptly.
F11Shorted / stuck keyKeypad.
F12 / F13Control board / EEPROM failureElectronic oven control.
F14Display tail not connectedRibbon connection or control.
F15Control board failureControl.
F20Communication failureHarness or boards.
F30 / F31Oven sensor open / shortedOven temperature sensor.
F90–F95Door lock circuit faults (motor, switch, control)Door lock motor assembly or control.
F1Control board faultControl.
F2Oven too hotSensor or relay.
F3 / F4Sensor open / shortedOven sensor.
F7Keypad faultKeypad.
F9Door lock faultLock assembly.

Common failures on these models

  • Ice maker and dispenser faults on 253 side-by-sides
  • Evaporator fan faults (SY EF) and defrost faults on 253 units
  • Drain pump and door lock faults on 417 washers (E20 / E41)
  • Heating element faults on 417 dryers (E64)
  • Drain restrictions and leaks on 587 dishwashers (i20 / i30)
  • Sensor and door lock faults on 790 ranges (F30 / F90)

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Kenmore 253 / 417 / 587 / 790 series questions

My Kenmore 790 range shows F10. What should I do?
F10 is runaway temperature. Turn the oven off at the breaker if it's heating uncontrolled and call; it's the sensor or relay board.
Do you repair every Kenmore 253 / 417 / 587 / 790 series model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Kenmore's factory warranty, call the manufacturer first.

Related refrigerator problems

Kenmore showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online