Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Kenmore
  4. 110 Series Washers & Dryers
Kenmore · Washer Repair · error codes

Kenmore 110-series washers & dryers (Whirlpool-built): error codes & what they mean

71 codes explained for 110.2xxxx – 110.2999x, 110.4xxxx, 110.6xxxx – 110.9xxxx models, with the part or problem behind each one. Same-day washing machine repair across Houston.

3 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Same places as the manufacturer that built it: under the lid or inside the door for laundry, inside the fresh-food section for refrigerators, on the door edge for dishwashers. The model number starts with the three-digit manufacturer prefix.

  • 110.2xxxx – 110.2999x (washers)Top-load washers: direct-drive (110.2xxx2) and VMW (110.2513x, 110.2613x, 110.2213x) and Cabrio-based Elite Oasis (110.2708x, 110.2808x).
  • 110.4xxxx (front-load washers)Elite HE3, HE4, HE5 and HE5t built on the Duet platform (110.4208x, 110.4508x, 110.4708x).
  • 110.6xxxx – 110.9xxxx (dryers)Electric and gas dryers, 29-inch (110.6xxxx electric, 110.7xxxx gas) and Elite HE dryers (110.8xxxx).

Example model numbers

  • 110.25132410
  • 110.26132411
  • 110.27082311
  • 110.42822200
  • 110.45862400
  • 110.62332510
  • 110.75132410
  • 110.87572601
How codes are displayed

Whirlpool-built Kenmores use Whirlpool's codes. VMW top loaders show F#E# pairs or flash the lid lock light; Oasis (Cabrio-based) models show two-digit F-codes; HE3/HE4/HE5 front loaders show Duet codes (F02, F21, F35); dryers show AF, L2, PF and F#E#.

A Kenmore model number starting with 110 was built by Whirlpool. That single fact determines which parts fit and which codes apply: the top loaders are Whirlpool VMW or Cabrio machines, the Elite HE front loaders are Duets, and the dryers are Whirlpool 29-inch dryers. We bring Whirlpool parts to 110-series calls.

The full code tables below cover the top loaders first, then the front loaders and dryers.

Kenmore 110 series washers & dryers error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
F0 E2Excessive sudsToo much or non-HE detergent; a worn drain path makes it worse.
F0 E3OverloadedReduce the load; repeat codes with small loads point at the drive.
F0 E4Rinse water temperature too highHoses reversed or thermistor.
F0 E5Unbalanced loadRedistribute; worn suspension rods if it repeats.
F1 E1Main control board failureControl board after checking console wiring.
F1 E2Motor control errorMotor windings and wiring, then the board.
F2 E1Stuck keyFree the key; UI board if it stays stuck.
F2 E3Control and user interface mismatchWrong replacement part installed; corrected.
F3 E1Water level pressure sensor faultAir hose to the pressure sensor, then the board (sensor is on-board).
F3 E2Inlet water temperature faultThermistor, which is part of the inlet valve harness.
F5 E1Lid switch fault (Start pressed with lid open)Lid lock/switch assembly.
F5 E2Lid lock faultDebris at the strike, then the lid lock assembly. The single most common code on these washers.
F5 E3Lid unlock faultLid lock assembly.
F5 E4Lid not opened between cyclesLid switch not detecting the lid; lid lock assembly.
F7 E1Basket speed sensor faultBasket must spin freely; then shifter assembly wiring, then the shifter.
F7 E5Shifter assembly faultShifter (mode actuator) assembly.
F7 E6Motor faultDrive motor or wiring.
F7 E7Motor can't reach target speedStuck garment or worn drive components.
F8 E1 / LFNot filling or long fillFaucets, hoses, inlet valves; board if water enters but isn't sensed.
F8 E3OverflowInlet valve leaking through, or board.
F8 E5Hot and cold hoses reversedSwap the hoses; thermistor harness if correct.
F9 E1 / LdLong drainDrain hose, pump obstruction, pump.

Elite Oasis / Cabrio codes

CodeWhat it meansWhat usually fixes it
F1 (Cabrio)Control board faultControl board.
F50 / F51Motor stalled / rotor position sensor faultRPS sensor, motor or a jammed basket.
F52 / F53 / F54Motor stop failure / motor overheated / motor overcurrentMotor, harness or a seized bearing.
F72Basket re-engagement failureBasket hub or drive block.
F70 / F71Communication errorHarness or boards.
F80 / F81 / F82Lid lock faultsLid lock assembly.
F32 / F40 / F41 / F42Pressure switch / temperature sensor faultsPressure switch or thermistor.
lid / dL / dULid open / lid lock / lid unlockLid lock assembly or strike.
oL / uLOverloaded / unbalancedReduce or redistribute the load; suspension if repeated.
Sd / SUDSuds detectedReduce detergent.
HCHot and cold hoses reversedSwap the hoses.

HE3 / HE4 / HE5 front-load codes (Duet platform)

CodeWhat it meansWhat usually fixes it
F05Water temperature sensor faultThermistor.
F06 / F25Motor tachometer faultMotor or MCU.
F07 / F10 / F15 / F31Motor control unit faultsMCU.
F09 / F27OverflowPressure switch or inlet valve.
F11 / F28Serial communication errorHarness between CCU and MCU, or boards.
F13 / F30Dispenser circuit faultDispenser motor.
F14EEPROM errorCentral control unit.
F23Heater faultHeater or relay.
F24Water temperature sensor faultThermistor.
F26 / F29Door switch / door unlock faultDoor lock assembly.
F32Pressure switch faultPressure switch.
F33Pump drive faultDrain pump.
F35Analog pressure sensor faultPressure sensor; often paired with SUD.
dL / dUDoor lock / unlock faultDoor lock assembly.
F0 E1 / rLLoad detected during Clean Washer cycleRemove items and rerun.
F0 E2Excessive sudsReduce HE detergent; clean the pump filter.
F0 E3OverloadedReduce the load.
F0 E5Unbalanced loadRedistribute; shocks if it repeats.
F1 E1Main control faultMain control board.
F1 E2Motor control faultMotor control / main board or motor.

Dryer codes

CodeWhat it meansWhat usually fixes it
AF / F4 E3Restricted airflowLint screen, transition hose, vent, exterior flap.
L2Low or no line voltageOne lost 240V leg: breaker, cord, outlet.
PFPower failure during cycleRestart; informational.
F1 E1Main control board failureControl board.
F2 E1Stuck keyKeypad.
F2 E5Configuration / board mismatchCorrect board or programming.
F3 E1Exhaust thermistor open or shortedExhaust thermistor.
F3 E2Moisture sensor faultClean the sensor bars; sensor if cleaning fails.
F3 E3Inlet thermistor open or shortedInlet thermistor near the heater.
F4 E1Heater circuit fault (relay stuck or element shorted)Heater relay or element; treated as urgent.
F4 E4Heating element open (electric)Element, thermal fuse or thermostat; vent checked for the root cause.
F5 E1Door switch faultDoor switch or strike.
F6 E1 / F6 E2Communication errorHarness or boards.
F01Primary control failureControl board.
F02Keypad / user interface failureUI or stuck key.
F22 / F23Exhaust thermistor open / shortedThermistor.
F24 / F25Inlet thermistor open / shortedInlet thermistor.
F28 / F29Moisture sensor open / shortedMoisture sensor or wiring.

Common failures on these models

  • Lid switches and motor couplings on direct-drive 110.2 washers
  • Lid locks and shifters on VMW 110.25/110.26 washers (F5 E2 / F7 E1)
  • Rotor position sensor and bearing faults on Elite Oasis (F51, roar on spin)
  • Drain pumps and door locks on HE3/HE4/HE5 (F21 / F22)
  • Thermal fuses, elements and idler pulleys on 110.6 and 110.7 dryers

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Kenmore 110 series washers & dryers questions

How do I know who built my Kenmore?
Read the first three digits of the model number. 110 is Whirlpool; 796 and 795 are LG; 253, 417, 587 and 790 are Frigidaire; 665 is Whirlpool dishwashers; 363 and 911 are GE; 401 is Samsung.
Do you repair every Kenmore 110 series washers & dryers model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Kenmore's factory warranty, call the manufacturer first.

Related washing machine problems

Kenmore showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online