Codes display as E plus two characters (E20, E41, E64). On many models the stored code is retrieved by waking the machine, waiting 5 seconds, then holding Start/Pause and Cancel together; the code shows while the buttons are held.
- Home
- Brands
- Frigidaire
- Washer
Frigidaire Front-load & top-load washers: error codes & what they mean
26 codes explained for FFFW / FFFS / FWF, ATF / FAFW / FAFS / LTF, FFTW / FFTL / FFTR models, with the part or problem behind each one. Same-day washing machine repair across Houston.
Models covered
Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the ceiling or upper wall. Dishwashers: left side of the door. Ranges: on the frame behind the door or drawer. Washers: inside the door rim.
- FFFW / FFFS / FWF (front-load)Front loaders (FFFW5000QW, FFFS5115PW, FWF4200QW) using the Affinity-derived E-codes.
- ATF / FAFW / FAFS / LTF (Affinity, 2005–2015)Affinity front loaders (ATF7000, FAFW3801LW, FAFS4473LW, LTF2940ES).
- FFTW / FFTL / FFTR (top-load)Top loaders (FFTW4120SW, FFTL1001QW) with limited display codes.
Example model numbers
- FFFW5000QW
- FFFS5115PW
- FWF4200QW
- ATF7000ES
- FAFW3801LW
- FAFS4473LW
- FFTW4120SW
Frigidaire and Affinity front loaders use Electrolux's E-code system, where the first digit names the system: E1x fill, E2x drain, E3x pressure sensing, E4x door lock, E5x motor, E6x heating, E7x temperature sensing, E9x communication. The common calls are E20/E21 (drain pump obstruction), E41 (door lock) and E5x motor codes that are often a loose tach connector rather than a dead motor.
Frigidaire washer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
E10 | Water not entering / low pressure | Supply, hoses, inlet valve. |
E11 | Fill time too long | Inlet valve, screens, pressure. |
E13 | Water leak in tub or air leak in air bell | Leak or pressure hose. |
E20 / E21 | Water not pumping out fast enough | Drain pump obstruction, hose, pump. |
E23 / E24 | Drain pump relay fault | Control board. |
E31 | Pressure sensor not communicating | Pressure sensor or board. |
E35 | Pressure sensor indicates overfill | Inlet valve or sensor. |
E41 | Control thinks door switch is open | Door lock assembly. |
E42 | Door remains locked at end of cycle | Door lock. |
E43–E48 | Door lock assembly or control faults | Door lock or board. |
E52 | Bad signal from tacho generator | Motor tach or harness. |
E55 | Motor overheating | Motor or overload. |
E56 / E57 / E58 | High motor current / inverter current | Motor, inverter or harness. |
E59 | No tacho signal for 3 seconds | Motor tach. |
E5A / E5B / E5C | Heat sink too hot (motor control) | Motor control board. |
E5D / E5E / E5F | Communication problem with motor control | Harness or boards. |
E66 | Heater relay failure | Control board. |
E67 | Input voltage incorrect on board | Board or supply. |
E68 | Current leakage to ground on heater | Heater or fuse. |
E71 / E74 / E75 / E76 | Water temperature sensor (NTC) faults | Thermistor or harness. |
E82 / E83 / E93 / E94 | Console or control configuration faults | UI or control board. |
E91 / E95 / E97 / E98 | Communication errors between UI and control | Harness or boards. |
EB1 / EB2 / EB3 | Line frequency or voltage out of limits | Household supply. |
EF1 | Clogged drain pump | Pump cleaned or replaced. |
EF2 | Too much detergent | Reduce detergent. |
EF5 | Water temperature too high | Thermistor or heater relay. |
No match in the main table; check the tables below or text us the code.
Common failures on these models
- Drain pump obstructions and failures (E20 / E21 / EF1)
- Door lock faults (E41–E48)
- Door boot mildew and tears
- Motor tach and current faults (E52 / E55–E59)
- Suds and detergent overdosing (EF2)
- Pressure sensor and overfill faults (E31 / E35)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.