Codes show on the display as i-codes (i20, i30) or two-letter codes (UO, ER, CL); models without a display flash the Start or Wash light. The code is often shown with a beep pattern.
- Home
- Brands
- Frigidaire
- Dishwasher
Frigidaire Dishwashers: error codes & what they mean
14 codes explained for FFCD / FFID / FDPC / FDSH, FGID / FGIP / FPID / FGHD, FDB / FDBB / PLD / GLD models, with the part or problem behind each one. Same-day dishwasher repair across Houston.
Models covered
Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the ceiling or upper wall. Dishwashers: left side of the door. Ranges: on the frame behind the door or drawer. Washers: inside the door rim.
- FFCD / FFID / FDPC / FDSH (Frigidaire)Front-control FFCD (FFCD2413US, FFCD2418US), top-control FFID (FFID2426TS), FDPC4221AS, FDSH4501AS.
- FGID / FGIP / FPID / FGHD (Gallery & Professional)FGID2466QF, FGID2479SF, FGIP2468UF, FPID2498SF, FGHD2465NF.
- FDB / FDBB / PLD / GLD (2000–2012)Older models with fewer codes.
Example model numbers
- FFCD2413US
- FFCD2418US
- FFID2426TS
- FDPC4221AS
- FGID2466QF
- FGID2479SF
- FGIP2468UF
- FPID2498SF
Frigidaire dishwashers use i-codes for the systems that fail most: i10 fill, i20/i40/iF0 drain and filters, i30 leak, i50 motor, i60 heating. Houston's hard water clogs the fine filters and spray arms on these units, and i20/i40 is frequently solved by a thorough filter and sump cleaning before any parts.
Frigidaire dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
i10 | Water level too low / not filling | Supply valve, hose, inlet valve. |
i20 / i40 / iF0 | Drain restricted or filters clogged | Filters, drain hose, pump. |
i30 | Leak into the base | Find the leak: gasket, sump seal, hoses. |
i50 | Wash motor or drain fault | Reset; circulation or drain pump. |
i60 | Water heating system error | Heater or thermistor. |
iC0 | Electronic control fault | Power reset; control board if it returns. |
UO | Vent plunger open | Vent assembly or wiring. |
UF | Vent fan wrong speed | Vent fan or board. |
ER | Touchpad failure / stuck key | Keypad. |
CE | Configuration error | Control board. |
tu | Turbidity sensor failure | Turbidity sensor. |
hs | Hall sensor error | Wash motor sensor. |
HO | Water temperature too low | Incoming hot water or heater. |
rA / RE / RF | Rinse aid switch faults | Dispenser assembly. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
PF | Power failure | Informational. |
CL | Door not latched | Close firmly. |
LO | Rinse aid low | Refill. |
Common failures on these models
- Drain restrictions and clogged filters (i20 / i40)
- Leaks into the base (i30) from gaskets and sump seals
- Heater faults (i60)
- Wash motor faults (i50)
- Vent assembly faults (UO / UF) leaving dishes wet
- Touchpad failures from steam (ER)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.