Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Frigidaire
  4. Dryer
Frigidaire · Dryer Repair · error codes

Frigidaire Electric & gas dryers: error codes & what they mean

21 codes explained for FFRE / FFRG / FFSE / FFSG, AEQ / FAQE / FASE / LEQ, Older FDE / GLER / FER models, with the part or problem behind each one. Same-day dryer repair across Houston.

3 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the ceiling or upper wall. Dishwashers: left side of the door. Ranges: on the frame behind the door or drawer. Washers: inside the door rim.

  • FFRE / FFRG / FFSE / FFSGElectric (FFRE4120SW, FFSE5115PW) and gas (FFRG4120SW, FFSG5115PW) dryers.
  • AEQ / FAQE / FASE / LEQ (Affinity, 2005–2015)Affinity dryers (AEQ7000ES, FAQE7001LW, FASE7074LW).
  • Older FDE / GLER / FERMechanical-timer dryers without codes.

Example model numbers

  • FFRE4120SW
  • FFSE5115PW
  • FFRG4120SW
  • FFSG5115PW
  • AEQ7000ES
  • FAQE7001LW
  • FASE7074LW
How codes are displayed

Codes display as E plus two characters (E20, E41, E64). On many models the stored code is retrieved by waking the machine, waiting 5 seconds, then holding Start/Pause and Cancel together; the code shows while the buttons are held.

Frigidaire and Electrolux dryers share a factory code set that is unusually precise about the heating circuit: E64 is an open heating element (the most common code), E63 is an element shorted to ground, E65 and E66 are the high-limit and thermal limiter, and E61/E67 are the heater relay and sensing on the board. EF1 and EF3 are airflow codes and point to the vent.

Frigidaire dryer error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
E31 / E32Moisture (contact) sensor frequency too high / too lowSensor bars, wiring; board if clean.
E42Door sensing failureControl board.
E51Motor relay failureControl board.
E52Motor stopped or not startingDrum friction, voltage, motor thermal protector, motor.
E53Motor centrifugal switch failureMotor.
E54Motor sensing failureControl board.
E61Heater relay failureControl board.
E63Heater shorted to groundHeating element.
E64Heater open circuitHeating element; the most common Frigidaire/Electrolux dryer code.
E65High-limit thermostat tripped repeatedlyVent restriction first, then limiter and high-limit.
E66Thermal limiter openThermal limiter; check for overheating cause.
E67Heater sensing failureControl board.
E71 / E72Outlet thermistor open / shortedOutlet thermistor.
E73 / E74Inlet thermistor open / shortedInlet thermistor.
E91 / E92 / E93 / E94 / E97Communication, protocol or configuration errorsBoards or console.
EA1 / EA2 / EA3Line frequency / voltage too high / too lowHousehold supply.
EA4Improper home wiringTerminal block L1-N-L2.
EA5Voltage sensing failureControl board.
EF1Vent blockedClear the vent; check thermistors.
EF3Maximum cycle time exceededVent, moisture sensor, thermistors.
EF8Key stuckConsole.

Common failures on these models

  • Open heating elements (E64)
  • High-limit and thermal limiter trips from restricted vents (E65 / E66)
  • Thermistor faults (E71–E74)
  • Motor faults and seized drum rollers (E52)
  • Moisture sensor film (E31 / E32)
  • Idler pulley and belt wear

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Frigidaire dryer questions

My Frigidaire dryer shows E64. Can I use it?
It won't heat. E64 is an open heating element, a same-visit replacement. We also check the vent, because overheating from restricted airflow is what usually kills the element.
Do you repair every Frigidaire dryer model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Frigidaire's factory warranty, call the manufacturer first.

Related dryer problems

Frigidaire showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online