Codes show on the oven display as F followed by two digits (F10, F30, F90). F10 (runaway temperature) should be addressed promptly; turn the oven off at the breaker if it keeps heating. Older models use single-digit F1–F9 codes.
- Home
- Brands
- Frigidaire
- Range & Oven
Frigidaire Ranges & wall ovens: error codes & what they mean
13 codes explained for FFEF / FFGF / FCRE / FCRG, FGEF / FGGF / FGEH / FGGH / FGIH, FPEF / FPGF / FPEH / FPGH models, with the part or problem behind each one. Same-day oven, range & stove repair across Houston.
Models covered
Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the ceiling or upper wall. Dishwashers: left side of the door. Ranges: on the frame behind the door or drawer. Washers: inside the door rim.
- FFEF / FFGF / FCRE / FCRG (freestanding)Electric (FFEF3054TS, FCRE3052AS) and gas (FFGF3054TS, FCRG3052AS) freestanding ranges.
- FGEF / FGGF / FGEH / FGGH / FGIH (Gallery)Gallery electric, gas and induction ranges (FGEF3036TF, FGGF3036TF, FGEH3047VF, FGIH3047VF).
- FPEF / FPGF / FPEH / FPGH (Professional)Professional ranges (FPEF3077QF, FPGF3077QF).
- FFEW / FGEW / FGET / FPEW (wall ovens)Single and double wall ovens.
Example model numbers
- FFEF3054TS
- FFGF3054TS
- FCRE3052AS
- FGEF3036TF
- FGGF3036TF
- FGEH3047VF
- FPEF3077QF
- FGEW3066UF
Frigidaire oven codes group by tens: F1x are control and keypad faults, F3x are the oven temperature sensor, F9x are the door lock circuit. F10 is the one to take seriously: the control saw a runaway temperature, which is either a failed sensor or a stuck relay on the board.
Frigidaire range & oven error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F10 | Runaway temperature | Oven sensor or relay board; address promptly. |
F11 | Shorted / stuck key | Keypad. |
F12 / F13 | Control board / EEPROM failure | Electronic oven control. |
F14 | Display tail not connected | Ribbon connection or control. |
F15 | Control board failure | Control. |
F20 | Communication failure | Harness or boards. |
F30 / F31 | Oven sensor open / shorted | Oven temperature sensor. |
F90–F95 | Door lock circuit faults (motor, switch, control) | Door lock motor assembly or control. |
No match in the main table; check the tables below or text us the code.
Older F1–F9 codes
| Code | What it means | What usually fixes it |
|---|---|---|
F1 | Control board fault | Control. |
F2 | Oven too hot | Sensor or relay. |
F3 / F4 | Sensor open / shorted | Oven sensor. |
F7 | Keypad fault | Keypad. |
F9 | Door lock fault | Lock assembly. |
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
PF | Power failure | Reset the clock. |
Common failures on these models
- Oven sensor faults (F30 / F31)
- Runaway temperature from relay boards (F10)
- Door lock motor faults after self-clean (F90–F95)
- Keypad faults from spills (F11)
- Bake element burnout (no code)
- Weak oven igniters on gas ranges (no code)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.