Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Problems
  3. Dryer Repair
  4. Dryer Takes Too Long
Dryer Repair · Houston, TX

Dryer taking too long to dry clothes?

Two or three cycles to dry a normal load is almost always airflow: a restricted vent, a crushed transition hose, a lint-packed blower or a stuck exterior flap. In Houston's humidity, a dryer with weak airflow barely dries at all.

One visit, 45–90 minutes Same-day in most of Houston 1-year parts, 90-day labor warranty
Quick diagnosis
Most likely cause
A restricted dryer vent
Typical repair time
One visit, 45–90 minutes
Service call
$89 diagnostic, credited to the repair

Why it's happening, in order of likelihood

Our technicians test in roughly this order. The numbers reflect how often each cause turns out to be the fault on Houston service calls.

  1. 1

    Restricted vent

    Lint accumulates in the duct, especially in long runs through two-story homes and roof terminations. Airflow drops, moisture can't escape, and the dryer runs hot and long. This is also the leading cause of dryer fires.

  2. 2

    Crushed or kinked transition hose

    The foil or vinyl hose behind the dryer gets crushed when the dryer is pushed back. Vinyl hose should be replaced with rigid or semi-rigid metal.

  3. 3

    Lint-packed blower housing or lint screen housing

    Lint bypasses the screen and packs the blower wheel and the chute below the screen.

  4. 4

    Stuck exterior damper

    The flap at the wall or roof sticks shut with lint or a bird's nest.

  5. 5

    Partially failed heating element or weak gas coils

    The dryer heats, but not enough.

  6. 6

    Moisture sensor coated with dryer-sheet residue

    Auto-dry cycles end early or run long because the sensor bars can't read the clothes.

  7. 7

    Overloading or washer not spinning well

    Clothes arriving too wet makes the dryer look slow.

Check these before you call

Safe, no-tools checks. If none of them solves it, the next step is a technician.

  • Feel the airflow at the exterior vent while the dryer runs; it should be strong.
  • Pull the dryer out and inspect the transition hose.
  • Clean the lint screen and wash it with soap to remove dryer-sheet film.
  • Wipe the moisture sensor bars inside the drum with rubbing alcohol.

Parts we typically replace

  • Transition hose (rigid metal)
  • Blower wheel
  • Heating element
  • Gas valve coils
  • Moisture sensor
  • Cycling thermostat

Brand-specific notes

  • LGLG d80/d90/d95 codes measure vent restriction directly.
  • WhirlpoolWhirlpool and Maytag AF codes mean restricted airflow.
  • SamsungSamsung models can show a vent-check indicator; clear the vent before assuming a part has failed.

Repair or replace?

Airflow problems are never a reason to replace a dryer.

What happens on the visit

1

Describe the symptom

Tell us the brand, model and what it's doing. A photo of the model tag helps.

2

We diagnose, you approve

$89 diagnostic, credited to the repair. Flat-rate quote before any work.

3

Fixed, usually that visit

Common parts are on the truck. 1-year parts, 90-day labor warranty on the repair.

Questions about this problem

Should I clean my dryer vent every year?
Yes, and more often for long runs or households with pets. We clear the vent at the dryer and check airflow as part of a repair; long runs may need a dedicated vent cleaning service.
Why does my dryer run hot but clothes stay damp?
Heat without airflow. The vent is restricted; the moisture has nowhere to go.

Related dryer problems

Dryer trouble? Same-day help.

Call or text (713) 548-7587 for a same-day appointment anywhere in Greater Houston. $89 diagnostic, credited toward your repair.

Call nowBook online