Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Electrolux
  4. Dryer
Electrolux · Dryer Repair · error codes

Electrolux Electric & gas dryers: error codes & what they mean

21 codes explained for ELFE / ELFG / EFME / EFMG, EIMED / EIMGD / EWMED / EIED, ELFE4222 / EFDE210 models, with the part or problem behind each one. Same-day dryer repair across Houston.

3 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Washers and dryers: inside the door rim. Refrigerators: inside the fresh-food section. Ovens: on the frame behind the door.

  • ELFE / ELFG / EFME / EFMGCurrent electric and gas dryers (ELFE7637AT, EFME627UTT, EFMG627UTT, EFME527UIW).
  • EIMED / EIMGD / EWMED / EIED (2008–2016)IQ-Touch and Wave-Touch dryers (EIMED60LT, EWMED70JIW, EIED55HIW).
  • ELFE4222 / EFDE210 (compact)24-inch compact ventless and vented dryers.

Example model numbers

  • ELFE7637AT
  • EFME627UTT
  • EFMG627UTT
  • EFME527UIW
  • EIMED60LT
  • EWMED70JIW
  • EIMED6CJIW
How codes are displayed

Codes display as E plus two characters (E20, E41, E64). On many models the stored code is retrieved by waking the machine, waiting 5 seconds, then holding Start/Pause and Cancel together; the code shows while the buttons are held.

Electrolux dryer codes come straight from the factory tech sheet and are precise: E64 open heater, E63 heater grounded, E65 high-limit trips, E66 thermal limiter, E71–E74 thermistors, E52 motor, EF1/EF3 airflow. The heating-circuit codes trace back to restricted venting more often than to a defective part.

Electrolux dryer error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
E31 / E32Moisture (contact) sensor frequency too high / too lowSensor bars, wiring; board if clean.
E42Door sensing failureControl board.
E51Motor relay failureControl board.
E52Motor stopped or not startingDrum friction, voltage, motor thermal protector, motor.
E53Motor centrifugal switch failureMotor.
E54Motor sensing failureControl board.
E61Heater relay failureControl board.
E63Heater shorted to groundHeating element.
E64Heater open circuitHeating element; the most common Frigidaire/Electrolux dryer code.
E65High-limit thermostat tripped repeatedlyVent restriction first, then limiter and high-limit.
E66Thermal limiter openThermal limiter; check for overheating cause.
E67Heater sensing failureControl board.
E71 / E72Outlet thermistor open / shortedOutlet thermistor.
E73 / E74Inlet thermistor open / shortedInlet thermistor.
E91 / E92 / E93 / E94 / E97Communication, protocol or configuration errorsBoards or console.
EA1 / EA2 / EA3Line frequency / voltage too high / too lowHousehold supply.
EA4Improper home wiringTerminal block L1-N-L2.
EA5Voltage sensing failureControl board.
EF1Vent blockedClear the vent; check thermistors.
EF3Maximum cycle time exceededVent, moisture sensor, thermistors.
EF8Key stuckConsole.

Common failures on these models

  • Open heating elements (E64)
  • Thermal limiter and high-limit trips from venting (E65 / E66)
  • Thermistor faults (E71–E74)
  • Motor faults (E52)
  • Moisture sensor faults (E31 / E32)
  • Drum roller and idler wear

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Electrolux dryer questions

Why does my Electrolux dryer keep showing E65?
The high-limit thermostat tripped too many times, almost always because airflow is restricted. We clear the vent and replace the limiter if it's weakened.
Do you repair every Electrolux dryer model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Electrolux's factory warranty, call the manufacturer first.

Related dryer problems

Electrolux showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online