Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Miele
  4. Dryer
Miele · Dryer Repair · error codes

Miele T1 heat-pump & classic dryers: error codes & what they mean

7 codes explained for TWB / TWF / TWI / TXD / TXR, T 8xxx / T 9xxx models, with the part or problem behind each one. Same-day dryer repair across Houston.

2 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Dishwashers: on the top edge of the door or the right side of the door frame. Washers and dryers: inside the door. Ovens: on the frame inside the door.

  • TWB / TWF / TWI / TXD / TXR (T1)T1 heat-pump ventless dryers: TWB120, TWF160, TWI180, TXD160, TXR860.
  • T 8xxx / T 9xxx (classic)Condenser and vented dryers from 2005–2016.

Example model numbers

  • TWB120 WP
  • TWF160 WP
  • TWI180 WP
  • TXD160 WP
  • TXR860 WP
  • T 8023 C
  • T 9802
How codes are displayed

Faults show as Technical fault F-number or messages such as Clean out airways, Empty container and Check filters. Heat-pump dryers depend on clean fluff filters and a clear heat exchanger; most slow-drying calls are maintenance.

Miele T1 dryers are ventless heat-pump machines, which suits Houston condos and townhomes with no exterior vent. Their faults are mostly airflow and condensate: F55 (not dry after 180 minutes) and the Check filters message usually mean lint in the fluff filters or heat exchanger; door lock codes (F32, F33) and sensor codes (F1–F4) are component faults.

Miele dryer error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
F1 / F2Heater NTC shorted / openSensor.
F3 / F4Fan NTC shorted / openSensor.
F32 / F33Door lock won't close / openDoor lock.
F36Door switch defectiveDoor switch.
F39 / F41 / F45 / F46Electronic, EEPROM, RAM or display faultsElectronic unit.
F55Laundry not dry after 180 minutesLint filters and heat exchanger cleaned; condensate pump.
F66Air path leakAir duct seals.

Messages that aren't faults

Things the display shows that don't mean a part has failed.

CodeWhat it meansWhat usually fixes it
Check filters / Clean out airwaysLint restrictionClean the fluff filters and heat exchanger filter.
Empty containerCondensate container fullEmpty it, or check the drain hose on plumbed units.

Common failures on these models

  • Lint restriction in filters and heat exchanger (F55)
  • Condensate pump faults
  • Door lock faults (F32 / F33)
  • NTC sensor faults (F1–F4)
  • Air path seal leaks (F66)

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Miele dryer questions

My Miele heat-pump dryer takes hours. Is it failing?
Usually it's lint in the secondary filter or heat exchanger. If a thorough cleaning doesn't restore drying, the condensate pump or compressor needs a look.
Do you repair every Miele dryer model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Miele's factory warranty, call the manufacturer first.

Related dryer problems

Miele showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online