Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Whirlpool
  4. Dishwasher
Whirlpool · Dishwasher Repair · error codes

Whirlpool Dishwashers: error codes & what they mean

26 codes explained for WDF330 – WDF560, WDT710 – WDT970 / WDTA50 – WDTA75, WDP370 / WDP540 models, with the part or problem behind each one. Same-day dishwasher repair across Houston.

4 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Washers: under the lid or inside the door frame. Dryers: inside the door. Refrigerators: inside the fresh-food compartment on the wall. Dishwashers: on the door edge. Ranges: on the frame behind the door or the drawer.

  • WDF330 – WDF560Front-control dishwashers (WDF330PAHS, WDF520PADM, WDF540PADM, WDF560SAFM).
  • WDT710 – WDT970 / WDTA50 – WDTA75Top-control dishwashers with Sensor cycle and third rack (WDT710PAHZ, WDT730PAHZ, WDT750SAHZ, WDT970SAHZ, WDTA50SAHZ, WDTA75SAHZ).
  • WDP370 / WDP540 (portable)Portable dishwashers.
  • Gold & Quiet Partner (2005–2012)GU2xxx, GU3xxx, DU1xxx, WDF750 with Clean-light blink codes.

Example model numbers

  • WDF520PADM
  • WDF540PADM
  • WDT710PAHZ
  • WDT730PAHZ
  • WDT750SAHZ
  • WDT970SAHZ
  • WDTA50SAHZ
  • GU2475XTVY
How codes are displayed

Newer models flash the Clean or Complete light in F#E# sequences or show the code on the display. 2005–2012 models report 'function codes' as blinks of the Clean light: count the blinks, pause, count again (7-1 means seven blinks, pause, one blink).

Whirlpool dishwashers (and the KitchenAid, Maytag, JennAir, Amana and Kenmore 665 units built on the same platform) report faults as F#E# pairs on newer models and as Clean-light blink codes on 2005–2012 models. The function numbers line up: an 8-1 blink code and an F8 E1 display both mean slow drain; 7-1 and F7 E1 both mean the heater isn't heating.

The most common codes we see are F8 E1 (slow drain, often the check valve or a chopper blade jam), F6 E1 (no water detected: inlet valve or float), F7 E1 (heater) and F2 E2 (user interface). Older units also blow the control board's thermal fuse, which leaves the panel dark.

Whirlpool dishwasher error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
F1 E1 / F1 E2Thermistor or optical water indicator (OWI) faultThermistor/OWI sensor in the sump.
F2 E1Stuck keyKeypad.
F2 E2User interface fault or mismatchUI board.
F3 E1 / F3 E2Thermistor / OWI faultSensor or dirty OWI lens.
F4 E1Wash motor fault / drain not completed before fillCirculation motor or drain issue.
F5 E1 / F5 E2Door switch open / door not latchedDoor latch or switch.
F6 E1No water detectedSupply valve, inlet valve, float.
F6 E2Water inlet valve electrical faultInlet valve or wiring.
F6 E3Suds or air in pumpWrong detergent or a fill problem.
F6 E4Float switch openOverfill float stuck or a leak into the sump area.
F6 E6 / F6 E7Incoming water too hot / flow meter faultWater heater setting or flow meter.
F7 E1Heating faultHeating element, thermal fuse or relay.
F7 E2Heater stuck onControl board relay.
F8 E1Slow drainCheck valve, drain path, pump.
F8 E2Drain pump electrical faultDrain pump or wiring.
F9 E1 / F9 E2Drain pump fault / stuck onDrain pump or control relay.
FA E1Dispenser faultDetergent dispenser.

Clean-light blink codes (2005–2012)

CodeWhat it meansWhat usually fixes it
1-1Stuck relay on control boardControl board.
2-1Stuck keyKeypad.
3-1 / 3-2Thermistor / OWI faultSensor.
5-1 / 5-2Door switch open / door not closedLatch or switch.
6-1 / 6-2 / 6-4No fill / inlet valve electrical / float switch openSupply, valve or float.
7-1 / 7-2Heater not heating / heater stuck onElement, fuse, board. Seven blinks of the Clean light is the classic heater fault.
8-1 / 8-2Slow drain / drain pump electricalDrain path or pump.
9-1Diverter motor position faultDiverter motor.
10-1Dispenser faultDispenser.

Common failures on these models

  • Slow drain from check valves, chopper assemblies and drain pumps (F8 E1 / 8-1)
  • No-fill faults from inlet valves and floats (F6 E1 / 6-1)
  • Heater and thermal fuse faults (F7 E1 / 7-1), the seven-blink classic
  • Dark control panels from blown thermal fuses on Gold-series units
  • Door latch faults (F5 E1 / 5-1)
  • Wash motor failures leaving dishes dirty (F4 E1)

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Whirlpool dishwasher questions

My Whirlpool dishwasher's Clean light blinks 7 times. What is it?
The heater circuit failed to heat: the element, the thermal fuse or the board. We test which and replace it the same visit.
What does F8 E1 mean?
Slow drain. We check the check valve, drain hose, disposal connection and pump.
Do you repair every Whirlpool dishwasher model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Whirlpool's factory warranty, call the manufacturer first.

Related dishwasher problems

Whirlpool showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online