Newer models flash the Clean or Complete light in F#E# sequences or show the code on the display. 2005–2012 models report 'function codes' as blinks of the Clean light: count the blinks, pause, count again (7-1 means seven blinks, pause, one blink).
- Home
- Brands
- KitchenAid
- Dishwasher
KitchenAid Dishwashers: error codes & what they mean
26 codes explained for KDTE / KDTM / KDPM / KDFE / KDPE, KDTE104 / KDTE334 / KDFE104, KUDE / KUDS / KUDI / KUDL models, with the part or problem behind each one. Same-day dishwasher repair across Houston.
Models covered
Find the model number on the rating plate. Dishwashers: left edge of the door. Refrigerators: inside the fresh-food compartment or on the top grille of built-ins. Ranges: on the frame behind the door.
- KDTE / KDTM / KDPM / KDFE / KDPECurrent top- and front-control models with ProWash and third rack (KDTE204KPS, KDTM404KPS, KDPM604KPS, KDFE204KPS, KDPE234GPS).
- KDTE104 / KDTE334 / KDFE104 (2013–2019)Mid-generation models on the Whirlpool platform.
- KUDE / KUDS / KUDI / KUDL (Superba, 2000–2012)Superba and Architect Series II with Clean-light blink codes and the thermal-fuse-on-the-board problem.
Example model numbers
- KDTE204KPS
- KDTM404KPS
- KDPM604KPS
- KDFE204KPS
- KDPE234GPS
- KDTE334GPS
- KUDE40FXSS
- KUDS30IXSS
KitchenAid dishwashers are the premium version of the Whirlpool platform and use the same codes: F8 E1 slow drain, F6 E1 no water, F7 E1 heater, F2 E2 user interface, with 2005–2012 Superba models blinking the Clean light instead. KitchenAid units are quieter and better built, which makes almost every fault worth repairing.
Superba-era units (KUDE/KUDS) are known for two things: a thermal fuse on the control board that blows and leaves the panel dark, and door latch switches that stop the cycle. Both are routine repairs.
KitchenAid dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 E1 / F1 E2 | Thermistor or optical water indicator (OWI) fault | Thermistor/OWI sensor in the sump. |
F2 E1 | Stuck key | Keypad. |
F2 E2 | User interface fault or mismatch | UI board. |
F3 E1 / F3 E2 | Thermistor / OWI fault | Sensor or dirty OWI lens. |
F4 E1 | Wash motor fault / drain not completed before fill | Circulation motor or drain issue. |
F5 E1 / F5 E2 | Door switch open / door not latched | Door latch or switch. |
F6 E1 | No water detected | Supply valve, inlet valve, float. |
F6 E2 | Water inlet valve electrical fault | Inlet valve or wiring. |
F6 E3 | Suds or air in pump | Wrong detergent or a fill problem. |
F6 E4 | Float switch open | Overfill float stuck or a leak into the sump area. |
F6 E6 / F6 E7 | Incoming water too hot / flow meter fault | Water heater setting or flow meter. |
F7 E1 | Heating fault | Heating element, thermal fuse or relay. |
F7 E2 | Heater stuck on | Control board relay. |
F8 E1 | Slow drain | Check valve, drain path, pump. |
F8 E2 | Drain pump electrical fault | Drain pump or wiring. |
F9 E1 / F9 E2 | Drain pump fault / stuck on | Drain pump or control relay. |
FA E1 | Dispenser fault | Detergent dispenser. |
No match in the main table; check the tables below or text us the code.
Clean-light blink codes (Superba era)
| Code | What it means | What usually fixes it |
|---|---|---|
1-1 | Stuck relay on control board | Control board. |
2-1 | Stuck key | Keypad. |
3-1 / 3-2 | Thermistor / OWI fault | Sensor. |
5-1 / 5-2 | Door switch open / door not closed | Latch or switch. |
6-1 / 6-2 / 6-4 | No fill / inlet valve electrical / float switch open | Supply, valve or float. |
7-1 / 7-2 | Heater not heating / heater stuck on | Element, fuse, board. Seven blinks of the Clean light is the classic heater fault. |
8-1 / 8-2 | Slow drain / drain pump electrical | Drain path or pump. |
9-1 | Diverter motor position fault | Diverter motor. |
10-1 | Dispenser fault | Dispenser. |
Common failures on these models
- Dark control panel from a blown board thermal fuse (Superba)
- Slow drain (F8 E1) from check valves and drain pumps
- Heater circuit faults (F7 E1 / 7 blinks)
- Door latch faults (F5 E1)
- Wash motor failures (F4 E1) on 2008–2014 units
- User interface faults (F2 E2)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.