Newer models flash the Clean or Complete light in F#E# sequences or show the code on the display. 2005–2012 models report 'function codes' as blinks of the Clean light: count the blinks, pause, count again (7-1 means seven blinks, pause, one blink).
Maytag Dishwashers: error codes & what they mean
26 codes explained for MDB4949 / MDB7959 / MDB8959 / MDB9959, MDB4709 / MDB7749 / MDB8969, Jetclean / MDB6xxx models, with the part or problem behind each one. Same-day dishwasher repair across Houston.
Models covered
Find the model number on the rating plate. Washers: under the lid on the top frame. Dryers: inside the door opening. Refrigerators: inside the fresh-food section. Ranges: behind the storage drawer.
- MDB4949 / MDB7959 / MDB8959 / MDB9959Top- and front-control dishwashers with PowerBlast (MDB4949SHZ, MDB7959SKZ, MDB8959SKZ, MDB9959SKZ).
- MDB4709 / MDB7749 / MDB8969 (older)2010–2017 models on the same Whirlpool platform.
- Jetclean / MDB6xxx (2000s)Older Jetclean units with blink codes.
Example model numbers
- MDB4949SHZ
- MDB7959SKZ
- MDB8959SKZ
- MDB9959SKZ
- MDB4709PAW
- MDB7749SBM
Maytag dishwashers use the Whirlpool dishwasher code set: F8 E1 slow drain, F6 E1 no fill, F7 E1 heater, F2 E2 user interface, with older units reporting the same faults as Clean-light blink codes. The chopper assembly and check valve behind the filter are the usual suspects for drain faults.
Maytag dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 E1 / F1 E2 | Thermistor or optical water indicator (OWI) fault | Thermistor/OWI sensor in the sump. |
F2 E1 | Stuck key | Keypad. |
F2 E2 | User interface fault or mismatch | UI board. |
F3 E1 / F3 E2 | Thermistor / OWI fault | Sensor or dirty OWI lens. |
F4 E1 | Wash motor fault / drain not completed before fill | Circulation motor or drain issue. |
F5 E1 / F5 E2 | Door switch open / door not latched | Door latch or switch. |
F6 E1 | No water detected | Supply valve, inlet valve, float. |
F6 E2 | Water inlet valve electrical fault | Inlet valve or wiring. |
F6 E3 | Suds or air in pump | Wrong detergent or a fill problem. |
F6 E4 | Float switch open | Overfill float stuck or a leak into the sump area. |
F6 E6 / F6 E7 | Incoming water too hot / flow meter fault | Water heater setting or flow meter. |
F7 E1 | Heating fault | Heating element, thermal fuse or relay. |
F7 E2 | Heater stuck on | Control board relay. |
F8 E1 | Slow drain | Check valve, drain path, pump. |
F8 E2 | Drain pump electrical fault | Drain pump or wiring. |
F9 E1 / F9 E2 | Drain pump fault / stuck on | Drain pump or control relay. |
FA E1 | Dispenser fault | Detergent dispenser. |
No match in the main table; check the tables below or text us the code.
Clean-light blink codes (older models)
| Code | What it means | What usually fixes it |
|---|---|---|
1-1 | Stuck relay on control board | Control board. |
2-1 | Stuck key | Keypad. |
3-1 / 3-2 | Thermistor / OWI fault | Sensor. |
5-1 / 5-2 | Door switch open / door not closed | Latch or switch. |
6-1 / 6-2 / 6-4 | No fill / inlet valve electrical / float switch open | Supply, valve or float. |
7-1 / 7-2 | Heater not heating / heater stuck on | Element, fuse, board. Seven blinks of the Clean light is the classic heater fault. |
8-1 / 8-2 | Slow drain / drain pump electrical | Drain path or pump. |
9-1 | Diverter motor position fault | Diverter motor. |
10-1 | Dispenser fault | Dispenser. |
Common failures on these models
- Slow drain from check valves and chopper jams (F8 E1)
- Inlet valve and float faults (F6 E1)
- Heater faults (F7 E1)
- Control board and UI faults (F1 E1 / F2 E2)
- Door latch faults (F5 E1)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.