Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. GE Appliances
  4. Dishwasher
GE Appliances · Dishwasher Repair · error codes

GE Appliances Dishwashers: error codes & what they mean

12 codes explained for GDF / GDT / GDP, PDT / PDP, GSD / PDW / GLD models, with the part or problem behind each one. Same-day dishwasher repair across Houston.

3 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the upper left wall. Washers: under the lid or behind the control panel. Dryers: inside the door. Dishwashers: on the tub rim or door edge. Ranges: on the frame behind the drawer or door.

  • GDF / GDT / GDP (current GE)Front-control GDF (GDF510PSRSS, GDF550PSRSS, GDF650SSJSS), top-control GDT (GDT550PSRSS, GDT630PSRSS, GDT665SSNSS, GDT695SSJSS) and GDP (GDP630PYRFS).
  • PDT / PDP (GE Profile) and CDT (Café)PDT715SYNFS, PDT785SYNFS, PDP715SYNFS, CDT845P2NS1; same platform with more features.
  • GSD / PDW / GLD (2000–2014)Older models that show the C1–C8 consumer error codes (PDW9880, GSD6660, GLD5600).

Example model numbers

  • GDF510PSRSS
  • GDF550PSRSS
  • GDT550PSRSS
  • GDT630PSRSS
  • GDT665SSNSS
  • PDT715SYNFS
  • PDT785SYNFS
  • PDW9880J
How codes are displayed

Current GE dishwashers show words (Leak Detected, H2O, PF) and lights rather than numeric codes; detailed faults are read in service mode. 2000–2014 GE, Profile and Monogram models show C1–C8 consumer codes on the display.

On a current GE dishwasher the message that matters is Leak Detected: the base-pan sensor is wet and the machine won't run until the leak is found and the pan dried. H2O means no water is reaching the tub. Everything else shows up as a symptom (not draining, not cleaning, not drying) and is diagnosed with the service-mode codes.

Older GE and GE Profile dishwashers (2000–2014) report consumer codes C1 through C8, which map neatly to drain, fill, temperature and dispenser faults.

GE Appliances dishwasher error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
Leak DetectedWater sensed in the base panPump seal, gasket, hose; the leak must be found before the unit will run.
H2OLow or no water supplySupply valve, inlet valve, hose.
PFPower failurePress Start/Reset; informational.
CL / LockControl lock onHold the lock key 3 seconds.

C1–C8 consumer codes (2000–2014 models)

CodeWhat it meansWhat usually fixes it
C1Drain took too long (over 2 minutes)Drain path, check valve, pump.
C2Drain not completed in 7 minutesDrain pump or blockage.
C3Dishwasher will not drainPump, hose, disposal knockout.
C4Overfill / flood switch trippedFloat switch, inlet valve, or a leak into the base.
C5Too little water in the tubWater supply, inlet valve, float.
C6Water temperature too lowIncoming water temperature or heater.
C7Water temperature sensor failureThermistor.
C8Detergent cup blockedDispenser obstructed or failed.

Common failures on these models

  • Leak Detected from pump seals, gaskets and hoses
  • Drain faults from pumps, check valves and disposal connections
  • Fine filter and spray arm clogging in Houston hard water
  • Wash motor failures on 2008–2016 units
  • Heater and vent faults leaving dishes wet
  • Door latch and switch faults

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

GE Appliances dishwasher questions

My GE dishwasher says Leak Detected but the floor is dry.
The base pan under the tub holds water before it reaches the floor. We find the source, dry the pan and the sensor, and the message clears.
What does C3 mean on an older GE dishwasher?
The dishwasher isn't draining: pump, hose or the disposal knockout plug.
Do you repair every GE Appliances dishwasher model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under GE Appliances's factory warranty, call the manufacturer first.

Related dishwasher problems

GE Appliances showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online