Most GE washers don't display consumer error codes. Faults are stored and read in a service mode (on front loaders, hold Start/Pause about 10 seconds until the display lights). Older Hydrowave top loaders flash an LED on the motor in counted patterns, listed below. When a current model does show a code, note it and text it to us.
- Home
- Brands
- GE Appliances
- Washer
GE Appliances Top-load & front-load washers: error codes & what they mean
10 codes explained for GTW335 – GTW845, GFW450 – GFW850, Hydrowave GTWN / GTWP / WJRE / WCVH models, with the part or problem behind each one. Same-day washing machine repair across Houston.
Models covered
Find the model number on the rating plate. Refrigerators: inside the fresh-food section on the upper left wall. Washers: under the lid or behind the control panel. Dryers: inside the door. Dishwashers: on the tub rim or door edge. Ranges: on the frame behind the drawer or door.
- GTW335 – GTW845 (top-load)Current top loaders with and without agitators (GTW335ASNWW, GTW465ASNWW, GTW485ASJWS, GTW500ASNWS, GTW720BSNWS, GTW840CSNWS); UltraFresh and Profile PTW models.
- GFW450 – GFW850 (front-load)Front loaders with UltraFresh Vent (GFW450SSMWW, GFW550SSNWW, GFW650SSNWW, GFW850SPNRS) and Profile PFW models.
- Hydrowave GTWN / GTWP / WJRE / WCVH (2006–2015)Older top loaders with the motor-LED flash codes below.
Example model numbers
- GTW335ASNWW
- GTW465ASNWW
- GTW485ASJWS
- GTW720BSNWS
- GFW450SSMWW
- GFW550SSNWW
- GFW650SSNWW
- GFW850SPNRS
GE washers keep their diagnostics mostly to themselves: the control stores fault codes that a technician reads in service mode, and the washer just stops or won't start. That makes the symptom the useful clue. A GE top loader that fills but won't agitate or spin is almost always the lid lock or the mode shifter; one that won't drain is the pump; one that won't fill is the inlet valve or its screens.
Older Hydrowave top loaders (2006–2015) do report faults, by flashing an LED on the motor. Those patterns are documented below because thousands of them are still running in Houston garages.
GE Appliances washer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
1 flash | Tub takes more than 25 seconds to stop | Brake or drive system. |
2 flashes | Belt slipping | Belt and pulleys. |
3 flashes | Software problem | Clear; motor if it returns. |
4 flashes | Mode shifter failure | Mode shifter. |
5 flashes | Motor problem | Motor. |
6 flashes | Motor locked | Mode shifter if frozen; otherwise motor. |
7 flashes | Four cycles without the lid switch opening | Lid switch. |
8 flashes | Motor overheated | Motor or drive. |
9 flashes | Brake resistor failed | Motor. |
10 flashes | No communication between motor and control (2010+) | Timer or control board. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
Lid Lock light flashing | Lid lock fault or stored code | Lid lock assembly or strike; code read in service mode. |
Sensing / Fill lights cycling | Washer waiting on water level | Supply valves, inlet valve, pressure sensor. |
Lock / Control Lock lit | Keypad locked | Hold the lock key 3 seconds. |
Common failures on these models
- Lid lock failures on GTW top loaders
- Mode shifter faults (fills but won't agitate or spin)
- Drain pump obstructions and failures
- Water inlet valve and clogged screens
- Door lock and boot faults on GFW front loaders
- Motor and inverter faults on Hydrowave units
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.