Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Amana
  4. Washer
Amana · Washer Repair · error codes

Amana Top-load washers: error codes & what they mean

22 codes explained for NTW4516 / NTW4519 / NTW4605 / NTW4705, NTW4600 / NTW4650 / NTW4700, Older NAV / ALW models, with the part or problem behind each one. Same-day washing machine repair across Houston.

3 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Washers: under the lid. Dryers: inside the door. Refrigerators: inside the fresh-food section.

  • NTW4516 / NTW4519 / NTW4605 / NTW4705Current top loaders (NTW4516FW, NTW4519JW, NTW4605EW, NTW4705EW).
  • NTW4600 / NTW4650 / NTW4700 (2010–2017)VMW top loaders on the same platform.
  • Older NAV / ALWMechanical-timer washers without display codes.

Example model numbers

  • NTW4516FW
  • NTW4519JW
  • NTW4605EW
  • NTW4705EW
  • NTW4650YQ
  • NTW4700YQ
How codes are displayed

Models with a digital display alternate F# and E# (F5 E2). Models with only lights flash the Lid Lock LED when a code is stored; a Wash light alone means long fill (F8 E1), a Spin light alone means long drain (F9 E1). Older Cabrio-style models show two-digit F-codes (F51, F72) and words like LF, Ld, uL and Sd.

Amana top loaders are Whirlpool VMW washers at a lower price, so they use the same codes and the same parts: F5 E2 lid lock, F7 E1 / F7 E5 shifter, F8 E1 fill, F9 E1 drain. Lights-only models flash the lid lock LED when a code is stored.

Amana washer error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
F0 E2Excessive sudsToo much or non-HE detergent; a worn drain path makes it worse.
F0 E3OverloadedReduce the load; repeat codes with small loads point at the drive.
F0 E4Rinse water temperature too highHoses reversed or thermistor.
F0 E5Unbalanced loadRedistribute; worn suspension rods if it repeats.
F1 E1Main control board failureControl board after checking console wiring.
F1 E2Motor control errorMotor windings and wiring, then the board.
F2 E1Stuck keyFree the key; UI board if it stays stuck.
F2 E3Control and user interface mismatchWrong replacement part installed; corrected.
F3 E1Water level pressure sensor faultAir hose to the pressure sensor, then the board (sensor is on-board).
F3 E2Inlet water temperature faultThermistor, which is part of the inlet valve harness.
F5 E1Lid switch fault (Start pressed with lid open)Lid lock/switch assembly.
F5 E2Lid lock faultDebris at the strike, then the lid lock assembly. The single most common code on these washers.
F5 E3Lid unlock faultLid lock assembly.
F5 E4Lid not opened between cyclesLid switch not detecting the lid; lid lock assembly.
F7 E1Basket speed sensor faultBasket must spin freely; then shifter assembly wiring, then the shifter.
F7 E5Shifter assembly faultShifter (mode actuator) assembly.
F7 E6Motor faultDrive motor or wiring.
F7 E7Motor can't reach target speedStuck garment or worn drive components.
F8 E1 / LFNot filling or long fillFaucets, hoses, inlet valves; board if water enters but isn't sensed.
F8 E3OverflowInlet valve leaking through, or board.
F8 E5Hot and cold hoses reversedSwap the hoses; thermistor harness if correct.
F9 E1 / LdLong drainDrain hose, pump obstruction, pump.

Common failures on these models

  • Lid lock failures (F5 E2), the most common code on this platform
  • Shifter / actuator faults leaving the washer agitating but not spinning (F7 E1 / F7 E5)
  • Drain pump obstructions (F9 E1 / Ld)
  • Suspension rod wear (F0 E5 / uL)
  • Inlet valve and screens (F8 E1 / LF)
  • Tub bearing roar on older Cabrio and Bravos units

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Amana washer questions

Is an Amana washer worth repairing?
For lid locks, shifters, valves and pumps, yes; parts are inexpensive and shared with Whirlpool. A tub bearing or transmission on a budget machine is a judgment call we'll make with you.
Do you repair every Amana washer model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Amana's factory warranty, call the manufacturer first.

Related washing machine problems

Amana showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online