Faults show on the display as F followed by two digits, or as a text message on newer models (Technical fault F11). Many faults are also stored for the service technician. Miele advises switching the machine off and on once; a repeated fault needs service.
Models covered
Find the model number on the rating plate. Dishwashers: on the top edge of the door or the right side of the door frame. Washers and dryers: inside the door. Ovens: on the frame inside the door.
- G 7xxx (G 7000 series)G 7106, G 7156, G 7316, G 7366, G 7566, G 7966 with AutoDos.
- G 5xxx (G 5000 series)G 5006, G 5056, G 5266, G 5892.
- G 4xxx / G 6xxx (2010–2019)G 4228, G 4998, G 6165, G 6785, G 6875 and relatives.
- Futura & Optima (2005–2012)Older Miele dishwashers with the same F-code system.
Example model numbers
- G 7106 SCU
- G 7316 SCU
- G 7566 SCVi
- G 5006 SCU
- G 5266 SCVi
- G 4228 SCU
- G 6785 SCVi
Miele dishwashers tell you which system failed: F11 drainage, F12/F13 water intake, F14 and F24/F25/F26 heating and pressure, F70 the float switch in the base (Miele's waterproof system), F53 and F67–F78 the circulation pump, F88 the turbidity sensor. Most are repairable with genuine Miele parts, and Miele units are built to make that worthwhile.
F11 is the frequent one and starts with the triple filter and the drain pump non-return valve. F70 means water reached the base; the leak has to be found before the machine will run again.
Miele dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F01 / F02 | Heater NTC shorted / open | Temperature sensor. |
F11 | Drainage fault | Triple filter, drain pump, non-return valve. |
F12 / F13 | Water intake fault | Supply, inlet valve, flow meter. |
F14 | Heater pressure switch fault | Pressure switch or circulation. |
F24 | Heater relay fault | Relay / electronic. |
F25 | Heater fault / target temperature not reached | Heater. |
F26 | Water temperature too high | Heater control. |
F32 | Door lock fault | Door lock (AutoOpen models). |
F51 | Heater relay defective | Electronic. |
F53 | Speed sensor fault | Circulation pump. |
F67 | Circulation pump speed too low | Circulation pump. |
F68 | Circulation pump running after switch-off | Electronic. |
F70 | Float switch activated (waterproof system) | Water in the base; find the leak. |
F78 | Circulation pump fault | Pump or electronic. |
F88 | Turbidity sensor fault | Sensor. |
No match in the main table; check the tables below or text us the code.
Common failures on these models
- Drainage faults (F11) from filters, pumps and non-return valves
- Water intake faults (F12 / F13) from valves and flow meters
- Waterproof system trips (F70) from leaks
- Heater and heater relay faults (F24 / F25 / F51)
- Circulation pump faults (F53 / F67 / F78)
- Door lock faults on AutoOpen models (F32)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.