Codes show on the display as i-codes (i20, i30, i60) or two-letter codes (UO, ER). The leak code i30 stops the machine until the base is dry.
- Home
- Brands
- Electrolux
- Dishwasher
Electrolux Dishwashers: error codes & what they mean
14 codes explained for EDSH / EDSP / EI24ID, EIDW / EWDW models, with the part or problem behind each one. Same-day dishwasher repair across Houston.
Models covered
Find the model number on the rating plate. Washers and dryers: inside the door rim. Refrigerators: inside the fresh-food section. Ovens: on the frame behind the door.
- EDSH / EDSP / EI24IDCurrent top- and front-control dishwashers (EDSH4944AS, EDSP4951AS, EI24ID81SS).
- EIDW / EWDW (2008–2016)IQ-Touch and Wave-Touch dishwashers (EIDW6305GS, EWDW6505GS).
Example model numbers
- EDSH4944AS
- EDSP4951AS
- EI24ID81SS
- EI24ID50QS
- EIDW6305GS
- EWDW6505GS
Electrolux dishwashers use the Frigidaire/Electrolux i-code set: i10 fill, i20/i40 drain and filters, i30 leak, i50 motor, i60 heating, iC0 control. Premium models have a vent fan and turbidity sensor that add UF and tu codes.
Electrolux dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
i10 | Water level too low / not filling | Supply valve, hose, inlet valve. |
i20 / i40 / iF0 | Drain restricted or filters clogged | Filters, drain hose, pump. |
i30 | Leak into the base | Find the leak: gasket, sump seal, hoses. |
i50 | Wash motor or drain fault | Reset; circulation or drain pump. |
i60 | Water heating system error | Heater or thermistor. |
iC0 | Electronic control fault | Power reset; control board if it returns. |
UO | Vent plunger open | Vent assembly or wiring. |
UF | Vent fan wrong speed | Vent fan or board. |
ER | Touchpad failure / stuck key | Keypad. |
CE | Configuration error | Control board. |
tu | Turbidity sensor failure | Turbidity sensor. |
hs | Hall sensor error | Wash motor sensor. |
HO | Water temperature too low | Incoming hot water or heater. |
rA / RE / RF | Rinse aid switch faults | Dispenser assembly. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
PF | Power failure | Informational. |
CL | Door not latched | Close firmly. |
LO | Rinse aid low | Refill. |
Common failures on these models
- Drain restrictions and filters (i20 / i40)
- Leaks into the base (i30)
- Heater faults (i60)
- Vent fan faults (UF)
- Turbidity sensor faults (tu)
- Wash motor faults (i50)
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.