Codes appear on the oven display as F followed by a number (F2, F3, F7, F9), sometimes with a second code on newer controls. GE's advice is to disconnect power for 30 seconds; a code that returns needs service.
Monogram Professional ranges, wall ovens & Advantium: error codes & what they mean
8 codes explained for ZGP / ZDP, ZTS / ZTD / ZKD / ZET, ZSB / ZSC models, with the part or problem behind each one. Same-day oven, range & stove repair across Houston.
Models covered
Find the model number on the rating plate. Built-in refrigerators: behind the top grille or inside the fresh-food section. Ranges and ovens: on the frame inside the door.
- ZGP / ZDP (professional ranges)36- and 48-inch gas (ZGP366NTSS, ZGP486NDTSS) and dual-fuel (ZDP366NPSS, ZDP486NDPSS) ranges.
- ZTS / ZTD / ZKD / ZET (wall ovens)Single and double wall ovens (ZTS90DPSNSS, ZTD90DPSNSS, ZET9050SHSS).
- ZSB / ZSC (Advantium)Advantium speedcook ovens and combination wall ovens (ZSB9231NSS, ZSC2201NSS).
- ZGU / ZHU / ZEU (cooktops)Gas, induction and electric cooktops.
Example model numbers
- ZGP366NTSS
- ZGP486NDTSS
- ZDP366NPSS
- ZTS90DPSNSS
- ZTD90DPSNSS
- ZSB9231NSS
- ZHU30RSPSS
Monogram ovens use GE's control architecture and F-codes (F2, F3, F4, F7, F9). Professional ranges add heavy-duty igniters, spark modules and convection fans that fail without a code. Advantium speedcook ovens combine a halogen lamp system with a magnetron, and either can fail; a dim or dead lamp or a loss of microwave heat shows as food not cooking rather than a code.
Monogram range & oven error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F0 / F1 | Keypad or control board fault (stuck key, failed touchpad or ERC) | Keypad ribbon or electronic range control. |
F2 | Oven over-temperature | Oven sensor, stuck relay or control. |
F3 | Oven temperature sensor open | Oven sensor or harness. |
F4 | Oven temperature sensor shorted | Oven sensor. |
F5 | Control board fault (watchdog / relay) | Electronic range control. |
F7 | Shorted or stuck key | Keypad or control. |
F9 | Door lock / latch circuit fault | Lock motor, latch switch or control. |
FC | Door lock circuit fault (some models) | Lock switch or control. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
PF | Power failure | Reset the clock. |
Common failures on these models
- Oven sensor faults (F3 / F4)
- Door lock and hinge faults on heavy doors (F9)
- Igniter and spark module faults on ZGP ranges
- Advantium halogen lamp and magnetron failures
- Convection fan motor failures
- Induction generator faults on ZHU cooktops
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.