Codes show on the display as E1, E3, E4, E6, E7, E8, Ec, Ed or EH. Models without a display flash the Glass, 90 Min and Rapid lights in a pattern: Rapid only = E1, 90 Min + Rapid = E3, Glass only = E4, Glass + 90 Min = E6, all three = E7.
Midea Midea-built dishwashers (Midea, Insignia, Hisense & others): error codes & what they mean
8 codes explained for MDF / MDT, NS-DWR / NS-DWH / NS-DWF, HUI / HDW models, with the part or problem behind each one. Same-day dishwasher repair across Houston.
Models covered
Find the model number on the rating plate. Inside the cabinet or on the back panel; laundry inside the door.
- MDF / MDT (Midea)Midea-branded front- and top-control dishwashers (MDF18A1AST, MDT24H3AST, MDT24P5AST).
- NS-DWR / NS-DWH / NS-DWF (Insignia)Best Buy Insignia dishwashers built by Midea (NS-DWR1SS, NS-DWH3SS, NS-DWF1WH).
- HUI / HDW (Hisense)Hisense dishwashers (HUI6220XCUS, HDW24U46).
- Countertop & 18-inch compactMidea-built countertop and compact units sold under several names.
Example model numbers
- MDF18A1AST
- MDT24H3AST
- MDT24P5AST
- NS-DWR1SS
- NS-DWH3SS
- HUI6220XCUS
- HDW24U46
Midea builds dishwashers for its own name and for Insignia, Hisense and several other labels, and they share one code set: E1 fill, E3 heating, E4 overflow (water in the base), E6/E7 temperature sensor, E8 diverter valve, Ec wash control, Ed display communication, EH cover (lid) on countertop units. The machines are inexpensive and most faults are worth fixing on units under five years old.
Midea dishwasher error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
E1 | Longer inlet time / not filling | Supply tap, inlet valve, hose. |
E3 | Heating fault: temperature not reached | Heater or thermistor; clean filters first. |
E4 | Overflow | Drain hose height, filters, inlet valve; water in base. |
E6 / E7 | Thermistor open / short circuit | NTC sensor or board. |
E8 | Distributary (diverter) valve fault | Diverter valve. |
Ec | Wash control system failure | Wash motor or electronics. |
Ed | Display-to-control communication failure | Harness or boards. |
EH | Cover doesn't open or close properly | Cover motor or obstruction. |
No match in the main table; check the tables below or text us the code.
Common failures on these models
- Water inlet timeouts (E1) from valves and low pressure
- Heating faults (E3) from heaters and dirty filters
- Overflow and base leaks (E4)
- Thermistor faults (E6 / E7)
- Diverter valve faults (E8) on dual-arm models
- Drain pump and hose problems
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.