Houston · Harris, Fort Bend & Montgomery counties
Mon–Sat 7am–7pmSame-day & next-day appointments (713) 548-7587
  1. Home
  2. Brands
  3. Gaggenau
  4. Dishwasher
Gaggenau · Dishwasher Repair · error codes

Gaggenau 200 & 400 Series dishwashers: error codes & what they mean

21 codes explained for DF 2xx, DF 4xx models, with the part or problem behind each one. Same-day dishwasher repair across Houston.

2 model series Most repairs in one visit 1-year parts, 90-day labor warranty

Models covered

Find the model number on the rating plate. Ovens: on the frame inside the door. Cooktops: on the underside. Dishwashers: on the door edge.

  • DF 2xx (200 Series)DF250760, DF260760, DF270760 fully integrated dishwashers.
  • DF 4xx (400 Series)DF480700, DF481700, DF481161 with push-to-open doors.

Example model numbers

  • DF250760
  • DF260760
  • DF270760
  • DF480700
  • DF481700
  • DF481161
How codes are displayed

Codes show on the display as E:xx on most models and as four-digit codes (E3100) on the newest ones; the two formats are listed together below. Models without a display flash cycle lights. E15 is the leak-protection switch in the base pan and will not clear until the pan is dry.

Gaggenau dishwashers are BSH machines at the top of the range and share the Bosch/Thermador code set: E15 leak protection, E24/E25 drain, E09 heater, E14–E18 water inlet and flow meter. Fully integrated and push-to-open installations add door mechanisms that fail without a code.

Gaggenau dishwasher error codes

Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.

CodeWhat it meansWhat usually fixes it
E01 / E0100Heat pump motor circuit fault at controlPower module.
E02 / E03 / E0103 / E0107Control board relay faultPower module.
E04 / E0105Heater electronics fault found in self-testPower module.
E05 / E0106Wash arm diverter circuit faultDiverter or power module.
E06 / E8000Door sensor circuit faultDoor switch.
E07 / E2130Zeolite (CrystalDry) fan motor faultDrying fan.
E09 / E20 / E2030 / E6001Heat pump internal heater faultFlow-through heater / pump assembly.
E10 / E2120Zeolite chamber heater faultZeolite heater.
E12 / E2060Limescale in heat pumpDescale; softener salt on models with one. Houston water makes this one common.
E14 / E3000Flow meter failure or filling problemFlow meter or inlet valve.
E15 / E3100Water in base; leak protection activeFind the leak (sump seal, gasket, hose, heater); never just tip and reset.
E16 / E17 / E3300 / E3400Water cannot enter correctlyInlet hose, valve, aquastop.
E18 / E3200Water level too low or not pumped correctlySupply flow, inlet valve.
E19 / E6900Detergent dispenser solenoid faultDispenser.
E21 / E6002Heat pump blockedDebris in the circulation pump.
E22 / E9240Filter blockedClean the filter.
E23 / E6101Drain pump blocked or faultyDrain pump.
E24 / E6103Not draining: blocked filter, hose, cover or disposal knockoutDrain path and pump cover.
E25 / E6102Drain pump blocked or pump cover looseClear the pump; reseat the cover.
E27 / E9001House voltage too lowElectrician if it repeats.
E6160PowerControl lower spray arm reference position not foundSpray arm drive.

Messages that aren't faults

Things the display shows that don't mean a part has failed.

CodeWhat it meansWhat usually fixes it
H:01–H:24Delay start timerPress +/– until h:00.
Red floor light / Check water / Salt / Rinse aidStatus indicatorsRefill salt or rinse aid; Check water means supply.
3 or 5 beepsLeak detected / water in baseTreated as E15.

Common failures on these models

  • Leak-protection trips (E15)
  • Drain faults (E24 / E25)
  • Heater faults (E09)
  • Push-to-open door mechanism faults
  • Flow meter and inlet faults (E14 / E17)

Before you call

  • Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
  • Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
  • Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
  • Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.

Gaggenau dishwasher questions

Do you repair fully integrated Gaggenau dishwashers?
Yes. Panel removal adds a little time; the repair itself follows the BSH platform.
Do you repair every Gaggenau dishwasher model?
Yes, out of warranty. Text us the full model number from the rating plate and the code on the display, and we'll bring the right part. If the unit is still under Gaggenau's factory warranty, call the manufacturer first.

Related dishwasher problems

Gaggenau showing a code? We'll bring the part.

Text the code and a photo of the model tag to (713) 548-7587. Same-day appointments across Houston.

Call nowBook online