Faults show as F1–F9 on the drawer's display or front badge, with a beep. Each drawer has its own motor, pump, lid and controller, so one drawer can fault while the other runs. F1 (flood switch) means water is in the base tray under the drawers.
- Home
- Brands
- Fisher & Paykel
- DishDrawer
Fisher & Paykel DishDrawer dishwashers (DD24 & DD60): error codes & what they mean
7 codes explained for DD24D / DD24DAX / DD24DCTX, DD24S / DD24SAX / DD24STX, DD24DI / DD24SI models, with the part or problem behind each one. Same-day dishwasher repair across Houston.
Models covered
Find the model number on the rating plate. DishDrawer: inside the drawer on the side wall. Washers: under the lid or on the back. Refrigerators: inside the fresh-food section.
- DD24D / DD24DAX / DD24DCTX (double)Double DishDrawers: DD24DAX9N, DD24DCTX9N, DD24DTX6PX1, DD24DV2T9N.
- DD24S / DD24SAX / DD24STX (single)Single DishDrawers: DD24SAX9N, DD24SCTX9N, DD24STX6PX1.
- DD24DI / DD24SI (integrated)Panel-ready integrated drawers.
- DD603 / DD605 / DS603 (2000–2010)First- and second-generation DishDrawers.
Example model numbers
- DD24DAX9N
- DD24DCTX9N
- DD24DTX6PX1
- DD24SAX9N
- DD24SCTX9N
- DD24DI9N
- DD603
DishDrawers are two independent dishwashers stacked in one cabinet, and their F-codes are short: F1 flood switch, F2 motor, F3/F4 temperature sensor or element, F5–F7 lid, F8/F9 electronics. The lid is the part people don't expect: a seal that lowers onto the drawer at the start of each cycle, driven by small actuators that wear and cause lid faults and leaks.
Fisher & Paykel dishdrawer error codes
Filter by code or symptom. Meanings are the documented common ones for these platforms; the tech sheet inside your appliance is authoritative for your exact model.
| Code | What it means | What usually fixes it |
|---|---|---|
F1 | Flood switch activated: water in the base | Turn off water and power; find the leak (lid seal, hose, pump). |
F2 | Motor problem | Wash motor / rotor. |
F3 | Temperature sensor failed / inlet water too hot | Incoming water above 150°F, or the sensor. |
F4 | Temperature sensor or element fault | Sensor or heater element. |
F5 / F6 / F7 | Lid fault | Lid actuator; power cycle may clear F5/F6. |
F8 | Electrical problem | Electronics / wiring. |
F9 | Electronics malfunction | Controller. |
No match in the main table; check the tables below or text us the code.
Messages that aren't faults
Things the display shows that don't mean a part has failed.
| Code | What it means | What usually fixes it |
|---|---|---|
U1–U6 style messages | User checks (drawer not closed, etc.) | Close the drawer fully; check for obstructions. |
Common failures on these models
- Flood switch trips (F1) from lid seals, hoses and pumps
- Lid actuator faults (F5–F7)
- Rotor / motor faults (F2)
- Element and sensor faults (F3 / F4)
- Drawer runner and front panel alignment issues
- Drain pump failures
Before you call
- Write down or photograph the exact code and which lights are lit before you reset anything; a reset can erase it.
- Reset once: switch the breaker off for 60 seconds, then back on. A code that returns is real.
- Check the basics the code points to (water valves open, drain hose not kinked, door fully closed, 240V breaker not half-tripped) using the table above.
- Text the code and a photo of the model tag to (713) 548-7587 so we arrive with the part.